2429307 - 5040A40 air conditioner condenser - r+r

Follow the safety instructions (See 5040 - Precautions)
Follow the safety instructions (See 5040 - Precautions)
Removing ( Refitting ) Place the vehicle on a lift. Drain the coolant (  - 0010T84  coolant for air conditioning system dehydrate and recharge ).  - 7210E10  R.R. FRONT BUMPER1. Undo the bolt (1a) and disconnect the connector (1b ) for the pipe from the condenser to the expansion valve.2. Undo the bolt (2a) and disconnect the connector (2b) for the pipe from the condenser to the compressor.
Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.
Removing ( Refitting ) Place the vehicle on a lift. Drain the coolant (  - 0010T84  coolant for air conditioning system dehydrate and recharge ).  - 7210E10  R.R. FRONT BUMPER1. Undo the bolt (1a) and disconnect the connector (1b ) for the pipe from the condenser to the expansion valve. 2. Undo the bolt (2a) and disconnect the connector (2b) for the pipe from the condenser to the compressor.
Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.
1. Undo the upper condenser fixing bolts.2. Remove the condenser (2a) lowering it, after having released it from the lower retainers.
1. Undo the upper condenser fixing bolts.2. Remove the condenser (2a) lowering it, after having released it from the lower retainers.
If necessary, remove the drier filter (refer to op. (5040A44)) If necessary, remove the drier filter (refer to op. (5040A44)) Refitting ( Removing ) Check that the condenser is intact and is not damaged and does not have deposits of dirt on the finned surface.If removed, refit the drier filter (refer to op. (5040A44))Place the condenser in position and attach it to the lower retainers.Tighten the upper condenser fixing bolts.1. Connect the connector (1a) for the pipe from the condenser to the compressor and secure it by tightening the bolt (1b) to the recommended torque.
Replace the O-rings for the connectors.
Only use green coloured seals, resistant to R134A coolant fluid.
Lubricate the thread of the connectors using anti-freeze.

FasteningComponentØValue(daNm)
1bBoltCOOLANT SYSTEM FITTINGSM60.9
2. Connect the connector (2a) for the pipe from the condenser to the expansion valve and secure it tightening the bolt (2b) to the recommended torque.

FasteningComponentØValue(daNm)
2bBoltCOOLANT SYSTEM FITTINGSM60.9
Refitting ( Removing ) Check that the condenser is intact and is not damaged and does not have deposits of dirt on the finned surface.If removed, refit the drier filter (refer to op. (5040A44))Place the condenser in position and attach it to the lower retainers.Tighten the upper condenser fixing bolts.1. Connect the connector (1a) for the pipe from the condenser to the compressor and secure it by tightening the bolt (1b) to the recommended torque.
Replace the O-rings for the connectors.
Only use green coloured seals, resistant to R134A coolant fluid.
Lubricate the thread of the connectors using anti-freeze.

FasteningComponentØValue(daNm)
1bBoltCOOLANT SYSTEM FITTINGSM60.9
2. Connect the connector (2a) for the pipe from the condenser to the expansion valve and secure it tightening the bolt (2b) to the recommended torque.

FasteningComponentØValue(daNm)
2bBoltCOOLANT SYSTEM FITTINGSM60.9
 - 7210E10  R.R. FRONT BUMPER Repressurize using coolant fluid (  - 0010T84  coolant for air conditioning system dehydrate and recharge ).  - 7210E10  R.R. FRONT BUMPER Repressurize using coolant fluid (  - 0010T84  coolant for air conditioning system dehydrate and recharge ).