2428869 - 1020D14 front crank shaft oil seal cover - r + r and replace seals for versions with oil pump on crank shaft, timing side

Removing ( Refitting ) Position the vehicle on the ramp. Proceed with removal  - 4450B04  right front wheel r r . Proceed with removal  - 7055B66  Engine compartment DUST SHIELD protection in right front wheel arch - R.R. . Proceed with removal  - 7055B91  Right front WHEEL ARCH LINER - R.R. . Proceed with removal  - 1008B10  power unit front mount (timing side) flexible block - replace . Proceed with removal  - 1008A46  cam shaft left rigid mount - r r . Proceed with removal  - 1032D12  timing system protective cover(s) - r + r . Proceed with removal  - 1092B40  air conditioner compressor/alternator drive belt - r + r . Proceed with removal  - 1092A10  Crankshaft services PULLEY - R.R. . Proceed with removal  - 1032B10  toothed timing belt - r + r for timing adjustment or replacement . Proceed with removal  - 1032B44  toothed drive pulley - r + r with timing belt removed . Proceed with removal  - 1088C14  water pump - r + r with drive belt removed . Proceed with removal  - 1048A10  air cleaner filtering element - replace . Proceed with removal  - 1072C44  exhaust manifold heat shield on bulkhead - r+r . Proceed with removal  - 1072C16  exhaust manifold with catalytic converter - r r . Proceed with removal  - 2110A60  manual gearbox/engine coupling bracket - r+r . Proceed with removal  - 1020A20  crank case oil sump - r + r clean seals for sealant application . Proceed with removal  - 1084B28  engine oil intake pump - r + r with crankcase sump removed . 1. Undo the bolt (1a) and move the engine rpm sensors (1b) to one side.2. Disconnect the electrical connection from the engine oil pressure warning light switch.

NameConnector
2Engine oil pressure sensor (switch)  K30 
3. Release and remove the engine oil filter using a suitable tool.
1. Undo the bolts (1a) and remove the crankshaft front oil seal cover (1b) assembly.
Refitting ( Removing ) Refit the crankshaft front cover and secure with bolts.Lubricate the gasket with engine oil, then efit the engien oil filter and screw on the filter fully by hand.Connect the electrical connection to the engine oil pressure warning light switch.Place the engine rpm sensor back in its housing and fix it using the bolt. Proceed with refitting  - 1084B28  engine oil intake pump - r + r with crankcase sump removed . Proceed with refitting  - 1020A20  crank case oil sump - r + r clean seals for sealant application . Proceed with refitting  - 2110A60  manual gearbox/engine coupling bracket - r+r . Proceed with refitting  - 1072C16  exhaust manifold with catalytic converter - r r . Proceed with refitting  - 1072C44  exhaust manifold heat shield on bulkhead - r+r . Proceed with refitting  - 1048A10  air cleaner filtering element - replace . Proceed with refitting  - 1088C14  water pump - r + r with drive belt removed . Proceed with refitting  - 1032B44  toothed drive pulley - r + r with timing belt removed . Proceed with refitting  - 1032B10  toothed timing belt - r + r for timing adjustment or replacement . Proceed with refitting  - 1092A10  Crankshaft services PULLEY - R.R. . Proceed with refitting  - 1092B40  air conditioner compressor/alternator drive belt - r + r . Proceed with refitting  - 1032D12  timing system protective cover(s) - r + r . Proceed with refitting  - 1008A46  cam shaft left rigid mount - r r . Proceed with refitting  - 1008B10  power unit front mount (timing side) flexible block - replace . Proceed with refitting  - 7055B91  Right front WHEEL ARCH LINER - R.R. . Proceed with refitting  - 7055B66  Engine compartment DUST SHIELD protection in right front wheel arch - R.R. . Proceed with refitting  - 4450B04  right front wheel r r . Refill the engine oil lubrication system  - 0010T11  engine oil check level and top up . Refill the engine cooling system with coolant  - 0010T20  coolant change . Remove the car from the ramps.