2427602 - P15 LUGGAGE COMPARTMENT DOES NOT OPEN WITH REMOTE CONTROL

When opening is controlled by means of the remote control unit, the boot lid does not open.

The boot lid opening command is received by the Body Computer Node via the internal radio aerial; the Body Computer Node releases the boot lock and releases is slightly. With the alarm on (if fitted), when the boot button is pressed using the remote control which operates its release, the system disables the volumetric/tilt modules and disables boot entry from perimeter protection (door and bonnet entry remaining activated). When the door lock is disengaged, the boot lid opens to operate the electric handle on the bonnet. In 'independent boot' mode, boot lid opening is implemented by means of a remote control unit or dowel on the mechnical key.

		Results of the tests
0	PRELIMINARY CHECK	All OK	Problems met	Operation
	Check the condition of the boot lock/release fuse.	Continue to Step 1	Fuse blown	Change the fuse
1	PRELIMINARY CHECK	All OK	Problems met	Operation
	Check remote control unit battery charge status	Continue to Step 2	Battery charge status insufficient	Replace the remote control unit battery changed
2	PRELIMINARY CHECK	All OK	Problems met	Operation
	Check the operation of the system using the second remote control unit supplied with the car.	Continue to Step 3	Fault persists	Continue to Step 4
3	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Connect the diagnostic equipment (Examiner) and check the defective remote control unit correctly stored in the Body Computer Node configuration.	Continue to Step 14	Remote control unit not stored in the Body Computer Node configuration.	Store the remote control unit (see Description and Operation).
4	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Connect the Examiner and ensure the remote control units are stored in the Body Computer Node configuration.	Continue to Step 5	Remote control units not stored in Body Computer Node configuration.	Store the remote control units (see Description and Operation).
5	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Keep the Examiner connected and check individual remote control keys are properly downloaded and operational while in parameter mode.	Continue to Step 6	Remote control unit signals have not been properly downloaded.	Continue to Step 10
6	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Keep the Examiner connected and check the body computer node : that there are no errors.	Continue to Step 7	Errors found: boot opening control relay short-circuited or circuit open.	Change the boot lid opening relay.
7	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Use active diagnosis to check boot lid opening	Continue to Step 13	Boot lid does not open	Continue to Step 8
8	ELECTRICAL CIRCUIT CHECK	All OK	Problems met	Operation
	Check the electrical connection between the body computer node and the boot lock.	Continue to Step 9	Electrical connector on boot lid handle not correctly connected.	Connec the electrical handle to the boot lid handle correctly
			Electrical connection broken or not insulated	Restore continuity/insulation of the electrical connection See   E3045  BOOT AND FUEL FLAP OPENING
9	CHECKING ELECTRICAL SIGNAL	All OK	Problems met	Operation
	Disconnect the boot lid electrical connector and check for a opening command signal.	Continue to Step 12	Opening command signal absent.	Continue to Step 13
10	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Use an Examiner to check for errors.	Continue to Step 13	Error found: radio receiver faulty	Continue to Step 11
11	ELECTRICAL CIRCUIT CHECK	All OK	Problems met	Operation
	Check the radio receiver aerial	Continue to Step 13	Connected the incorrectly connected aerial to the radio receiver	Connect the aerial connect to the Body Computer Node correctly.
			Radio receiver aerial broken	Change the radio receiver aerial.
12	CHECK ON CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present.	End of diagnosis	Fault persists	Change the boot lid lock.
13	CHECK ON CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present.	End of diagnosis	Fault persists	Replace the body computer node
14	CHECK ON CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present.	End of diagnosis	Fault persists	Change the remote control unit