5040A20 AIR CONDITIONER COMPRESSOR - R+R - INCLUDES FLUID LEVEL CHECK AND TOP UP IF NECESSARY - Lancia - Ypsilon - eLearn

2429305 - 5040A20 air conditioner compressor - r+r - includes fluid level check and top up if necessary

Follow the safety instructions (See 5040 - Precautions)

) Place the vehicle on a lift. Drain the coolant ( - 0010T84 coolant for air conditioning system dehydrate and recharge ). - 4450B04 right front wheel r r - 7055B91 Right front WHEEL ARCH LINER - R.R. - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R.1. Fit a spanner (1a) in the services belt tensioner socket (1b) and rotate it in the direction of the arrow, then release and remove the services belt (1c).

1. Undo the bolts (1a) and remove the belt guard (1b) from the compressor. 2. Undo the blt (2a) releasing the bracket (2b).3. Undo the bolt (3a) and disconnect the connector (3b) for the pipe from the compressor to the condenser.4. Undo the bolt (4a) and disconnect the connector (4b) for the pipe from the compressor to the expansion valve.

Seal the disconnected connectors, using suitable plugs, to prevent humidity and impurities from entering the system.

1. Disconnect the electrical connection.

	Name	Connector
1	Air conditioning compressor electro-magnet	L20

2. Undo the compressor fixing bolts.3. Keep the compressor.

If replacing the compressor, proceed as follows.1. Drain the fluid contained in the compressor throught the openings connected to the pipes. If necessary, rotate the compressor several times and rotate the pulley, manually, to remove all the fluid.

The fluid is extremely hygroscopic: avoid leaving the containers open. Avoid leaving the compressor or any other component disconnected from the system for longer than is strictly necessary.

1. Recover the fluid drained from the compressor in a suitable transparent container (quantity A).2. Drain and recover the fluid from the new compressor (quantity B) in an identical container, following the instructions given previously.3. Introduce the same amount of fluid removed from the compressor being replaced into the new compressor (eliminate quantity C = B - A).

Refitting ( Removing

) Check that the compressor is not damaged.1. Reposition the compressor.2. Tighten the bolts fixing the compressor.

	Fastening	Component	Ø	Value(daNm)
2	Bolt	AIR CONDITIONER ASSEMBLY COMPRESSOR	M8	2.5

3. Connect the electrical connection.

1. Connect the connector (1a) for the pipe from the compressor to the expansion valve, compressor side and secure it tightening the bolt (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	COOLANT SYSTEM FITTINGS	M6	0.9

Replace the O-rings for the connectors. Only use green coloured seals, resistant to R134A coolant fluid. Lubricate the thread of the connectors using anti-freeze.

2. Connect the connector (2a) for the pipe from the compressor to the condenser, compressor side and secure it by tightening the bolt (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	Bolt	COOLANT SYSTEM FITTINGS	M6	0.9

3. Position the bracket (3a) and tighten the bolt (3b).4. Position the compressor belt guard (4a) and secure it using the bolts (4b).

Lower the vheicle and refit the services belt moving the tensioner using the spanner. - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R. - 7055B91 Right front WHEEL ARCH LINER - R.R. - 4450B04 right front wheel r r Repressurize using coolant fluid ( - 0010T84 coolant for air conditioning system dehydrate and recharge ). Remove the vehicle from the lift.