1056B90 SYSTEM CABLE BUNDLE - R + R - Lancia - Ypsilon - eLearn

2429001 - 1056B90 system cable bundle - r + r

) Position the vehicle on the ramp. Proceed with removal - 5530B10 battery - r+r . Proceed with removal - 5530B52 Battery DRIP TRAY/SUPPORT - R.R. . Proceed with removal - 1048A10 air cleaner filtering element - replace . 1. Loosen the band and disconnect the engine oil vapour intake pipe and the side of the sleeve from the air cleaner to the intake manifold2. Loosen the band, disconnect the hose from the air filter to the intake manifold, intake manifold side and remove it.

1. Disconnect the electrical connections from the ignition coils.

	Name	Connector
1	Ignition 'coil	A30

2. Disconnect the electrical connection from the cam angle sensor.

	Name	Connector
2	Timing sensor	K47

1. Disconnect the electrical connection for the front Lambda sensor for the catalytic converter.

	Name	Connector
1	Lambda sensor downstream of post-catalyzer	K17

2. Disconnect the electrical connection for the rear Lambda sensor for the catalytic converter.

	Name	Connector
2	Lambda sensor downstream of post-catalyzer	K17

1. Disconnect the electrical connection from the engine coolant temperature sensor.

	Name	Connector
1	Engine temperature sender unit	K36

2. Disconnect the electrical connection from the throtle body integrated with the M.D.S.

	Name	Connector
2	Integrated throttle body actuator	N75

1. Disconnect the electrical connections (1a) and (1b) from the injection/ignition system control unit.

	Name	Connector
1a	Engine management control unit	M10A

	Name	Connector
1b	Engine management control unit	M10B

2. Release system wiring loom (2a) from band (2b).3. Undo the nut (3a) and disconnect the earth lead (3b) from the injection-ignition system.

	Name	Connector
3b	Injection ECU earth	C60

4. Disconnect the electrical connection from the fuel vapour solenoid valve.

	Name	Connector
4	Fuel vapour recovery solenoid	L10

1. Undo the nut (1a) and disconnect the earth lead (1b) from the air conditioner compressor.

	Name	Connector
1b	Compressor earth	C39

2. Disconnect electrical connection (2a) from the intake air pressure/temperature sensor and release the electrical wiring from band (2b).

	Name	Connector
2a	Integrated air temperature sensor	K43

3. Disconnect the electrical connections from the injectors.

	Name	Connector
3	Injector	N70

1. Open the cover (1a), undo the nuts (1b) and disconnect the electrical connections (1c) for the alternator.

	Name	Connector
1c	Starter' motor	A20

2. Undo nut (2a) and disconnect earth lead (2b).3. Disconnect the electrical connection for the knock sensor.

	Name	Connector
3	Detonation sensor	K50

4. Disconnect the electrical connection from the air conditioning compressor engagement electromagnet.

	Name	Connector
4	Air conditioning compressor electro-magnet	L20

5. Release system wiring loom (5a) from bands (5b) on teh air capacity chamber.

Withdraw the system wiring loom from the throttle body side.1. Disconnect the front engine coupling.

	Name	Connector
1	Front / engine coupling	D4C

2. Remove the cover from the junction unit.

1. Undo the nut (1a) and disconnect the electrical connections (1b).

	Name	Connector
1b	Engine compartment junction unit	B1X

2. Disconnect engine front couplings (2a) and (2b).

	Name	Connector
2a	Front / engine coupling	D4A

	Name	Connector
2b	Front / engine coupling	D4B

3. Turn the junction unit and disconnect the front facia junction.

	Name	Connector
3	Front / dashboard coupling	D1

Proceed with removal - 4450B04 right front wheel r r . Proceed with removal - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R. . Proceed with removal - 1008B10 power unit front mount (timing side) flexible block - replace . Proceed with removal - 1032D12 timing system protective cover(s) - r + r . 1. Disconnect the electrical connection for the rpm sensor.

	Name	Connector
1	Rpm sensor	K46

2. Disconnect the electrical connection from the engine oil pressure warning light switch.

	Name	Connector
2	Engine oil pressure sensor (switch)	K30

Remove the system cable loom.

Refitting ( Removing

) Place the system cable loom back in its housing.Connect the electrical connection to the engine oil pressure warning light switch.Connect the electrical connection for the rpm sensor. Proceed with refitting - 1032D12 timing system protective cover(s) - r + r . Proceed with refitting - 1008B10 power unit front mount (timing side) flexible block - replace . Proceed with refitting - 7055B66 Engine compartment DUST SHIELD protection in right front wheel arch - R.R. . Proceed with refitting - 4450B04 right front wheel r r . Connect the front facia junction, then refit the junction unit in its housing. Connect the front engine couplings.Connection the electrical connections and fasten them using the nut.Refit the junction unit cover.Connect the front engine coupling.Secure the system wiring harness with fastenings to the air chamber.Connect the electrical connection to the air conditioner compressor electromagnet.Connect the electrical connection for the knock sensor.Connect the earth lead and fix it using the nut.Connect the electrical connection to the starter motor, secure it with the nut and close the protective cover.Connect the electrical connections to the injectors.Connect the electrical connection to the intake air temperature/pressure sensor and secure the electrical wiring with a collar.Connect the earth lead to the air conditioner compressor and fix it using the nut. Connect the electrical connection to the fuel vapour solenoid valve.Connect the earth lead to the injection-ignition system control unit and secure with the nut. Secure the system wiring loom with the band.Connect the electrical connections to the fuel injection/ignition control unit. Connect the electrical connection to the throttle body integral with M.D.S.Connect the electrical connection to the engine coolant temperature sensor.Connect the electrical connection for the rear Lambda sensor for the catalytic converter.Connect the electrical connection for the front Lambda sensor for the catalytic converter.Connect the electrical connection to the cam angle sensor.Connect the electrical connections to the ignition coils.Place the hose from the air filter to the intake manifold back in its housing, connect it to the intake manifold and tighten the band.Connect the engine oil vapour intake pipe on the side of the sleeve from air filter to intake manifold and tighten the band. Proceed with refitting - 1048A10 air cleaner filtering element - replace . Proceed with refitting - 5530B52 Battery DRIP TRAY/SUPPORT - R.R. . Proceed with refitting - 5530B10 battery - r+r . Remove the car from the ramps.