4130B20 POWER STEERING PUMP R R - Alfa - 156 - eLearn

3238134 - 4130B20 power steering pump r r

) Position the vehicle on the ramp Proceed with removal - 1016A40 ignition coil cover on cylinder head- r+r . Proceed with removal - 1008C10 power unit upper reaction link r r . Proceed with removal - 4130B10 power steering fluid resevoir r r . Proceed with removal - 1016A40 ignition coil cover on cylinder head- r+r . Proceed with removal - 4130B10 power steering fluid resevoir r r . 1. Disconnect the the delivery hose to the power assisted steering box from the power steering pump.

1. Release the timing sensor wiring from the collar on the protection.2. Undo the bolts (2a) and remove the protection (2b).

Proceed with removal - 7055B54 under-engine guard - r r . Proceed with the removal - 4450B10 Front WHEEL (one) - R.R. (Right side). Proceed with the removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side). Proceed with removal - 1092G10 single engine belt r r . 1. Keep the pump shaft secured and undo the bolts (1a) and remove the power steering pump pulley (1b).2. Undo the bolts (2a) and remove the power steering pump (2b).

Refitting ( Removing

) Place the power assisted steering pump back in its housing and fix it tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	POWER STEERING PUMP	M8	(Support side) 1.9 ÷ 2.3

Place the power assisted steering pump pulley back in its housing and tighten the bolts while keeping the pump shaft secured.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	POWER STEERING PUMP DRIVE PULLEY	M6	(Power assisted steering pupm side) 0.6 ÷ 0.8

Proceed with refitting - 1092G10 single engine belt r r . Proceed with the refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. (Right side). Proceed with the refitting - 4450B10 Front WHEEL (one) - R.R. (Right side). Proceed with refitting - 7055B54 under-engine guard - r r . Place the protection back in its housing and secure it using the bolts.Secure the timing sensor wiring using the collar on the protection.Connect the supply pipe to the power assisted steering box to the power assisted steering pump and tighten the connector to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Connector	PIPE BTWN PUMP + POWER STEERING BOX	M16	(Power steering pump side) 3.8 ÷ 4.2

Proceed with refitting - 4130B10 power steering fluid resevoir r r . Proceed with refitting - 1016A40 ignition coil cover on cylinder head- r+r . Proceed with refitting - 4130B10 power steering fluid resevoir r r . Proceed with refitting - 1008C10 power unit upper reaction link r r . Proceed with refitting - 1016A40 ignition coil cover on cylinder head- r+r . Fill the power steering circuit with the recommended fluid.

	Type	Component	Name	Qty.
-	Fluid	POWER ASSISTED STEERING CIRCUIT	TUTELA GI/A	-

Bleed the power steering system as described belowWith the front wheels raised off the ground, with the engine switched off turn the steering wheel to full lock, left and right, 4-5 times. Check and, if necessary, top up the fluid level in the reservoir. Remove the car from the ramps.Start the engine and carry out 4 - 5 full steering wheel turn cycles (right and left). Top up the fluid level in the reservoir.