1084C10 ENGINE OIL HEAT EXCHANGER - R + R - Alfa - 156 - eLearn

3237617 - 1084C10 engine oil heat exchanger - r + r

) Position the vehicle on the ramp. Proceed with removal - 7055B54 under-engine guard - r r . 1. Disconnect the lower radiator hose from the water pump rigid inlet pipe.

Recover the engine coolant in a suitable container.

1. Release and remove the engine oil filter using a suitable tool.

1. Undo the bolts fixing the coolant supply pipe to the engine oil heat exchanger.2. Loosen the connector of the coolant outlet pipe from the engine oil heat exchanger on the water pump rigid inlet pipe side.

1. Undo the connector securing the engine oil heat exchanger.2. Loosen the bands (2a) and disconnect the engine coolant inlet and outlet pipes (2b) from the engine oil heat exchanger.3. Remove the engine oil heat exchanger.

Refitting ( Removing

) Connect the water inlet and outlet pipes to the heat exchanger and secure them using the bands.Place the engine oil heat exchanger back in its housing and secure it using the pin.Tighten the connector of the coolant outlet pipe from the engine oil heat exchanger on the water pump rigid inlet pipe side.Tighten the bolts fixing the coolant supply pipe to the engine oil heat exchanger.Refit the engine oil filter in its seating and tighten it fully by hand.Connect the lower radiator hose to the water pump rigid inlet pipe.Supply the engine cooling system with the recommended fluid.

	Type	Component	Name	Qty.
-	Fluid	ENGINE COOLING CIRCUIT	Mixture 50% Paraflu11 for Alfa Romeo/distilled water	6.9

Top up the engine oil lubrication circuit using the recommended oil.

	Type	Component	Name	Qty.
-	Oli [l]	ENGINE LUBRICATION CIRCUIT	SELENIA 20K	4.4

For a distinctly sporty performance, use the recommended oil for the lubrication circuit.

	Type	Component	Name	Qty.
-	Oli [l]	ENGINE LUBRICATION CIRCUIT	SELENIA RACING	4.4

For the optimum operation of the engine in particularly harsh climatic conditions (temperatures below -20 degrees C), use the recommended oil for the engine lubrication circuit.

	Type	Component	Name	Qty.
-	Oli [l]	ENGINE LUBRICATION CIRCUIT	SELENIA PERFORMER	4.4

Proceed with refitting - 7055B54 under-engine guard - r r . Remove the car from the ramps.

Removing ( Refitting

) - 1088D10 lower sleeve for coolant outlet from radiator - r + r . - 4450B10 Front WHEEL (one) - R.R. . - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. . - 1092G10 single engine belt r r . - 5040A26 compressor mount - r r . Remove the cartridge engine oil filter using a suitable tool.

Collect the engine oil in a suitable container.

1. Unscrew the fitting.2. Disconnect the rubber coolant inlet and outlet pipes from the rigid pipes.3. Remove the engine oil heat exchanger complete with rubber hoses.

Refitting ( Removing

) Place the engine oil heat exchanger with sleeves back in its housing and secure by tightening the connector to the specified torque.

	Fastening	Component	Ø	Value(daNm)
-	Connector	ENGINE OIL HEAT EXCHANGER	-	3.0

Refit the engine oil filter in its seating and tighten it fully by hand after lubricating the gasket with engine oil.Top up the engine cooling system with the recommended fluid.

	Type	Component	Name	Qty.
-	Fluid [l]	ENGINE COOLING CIRCUIT	Mixture 50% Paraflu11 for Alfa Romeo/distilled water	6.8

- 5040A26 compressor mount - r r . - 1092G10 single engine belt r r . - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. . - 4450B10 Front WHEEL (one) - R.R. . - 1088D10 lower sleeve for coolant outlet from radiator - r + r .