3238392 - 5505A26 bonnet wiring - r r
 | For precise identification of the electrical connections, see Wiring Diagrams Section. |
Removing
(
Refitting
)
Place the vehicle on a lift
and remove the front wheels. - 5010C12 Windscreen demising VENT - R.R. - 7040A37 fuse box cover - r r - 7040A44 facia lh side cover - r r - 7040G24 switch for facia compartment light - r+r - 7040G20 facia compartment light bulb holder - r+r - 7040A31 flap assembly - r r - 7040A09 passenger air bag compartment cover - r r - 7040A65 passenger compartment box lock , one , r r
(right
and left)
- 5040D22 control (one) of air conditioner control support
- arrange - 7065C42 ashtray (one) r+r - 5570T80 car radio unit - r+r - 2125C24 gear lever knob - r + r - 7040A60 under facia trim - r+r - 3380A44 handbrake/linkage protection - r+r - 7040L28 tunnel switch panel - r r - 7040L20 tunnel trim - r r - 5560C51 combined analogue control panel - r+r or replace - 5540C18 headlamp/light cluster alignment correction motor
switch - r+r - 5560C60 anomaly display - r+r - 5560B02 kilometre/mileometer - r r - 5560B03 rev counter - r r - 5580C18 air bag module - r+r | Before working on the Air Bag system, follow the safety instructions for working on the system very carefully (See 5580C - Air Bag System - Precautions). |
Refitting
(
Removing
)
Check that the wiring is undamaged
and that the individual conductors are firmly attached to the connections.Check that the connections are fitted with
anti-slip devices (secondary lock).If necessary, check the continuity.Refit the front wiring harness by inserting
from the engine bay.Refit the rubber pad in the partition.Connect the electrical connection to the
engine wiring.Connect the various electrical connections.Fit the retaining clips to the front brake
pade sensor left and right wires.Use the probes fitted during removal to
insert the side flasher electrical wires and the windscreen wiper motor
lead.Secure the windscreen wiper motor lead
using a retaining clip.Connect the windscreen wiper motor electrical
connection and refit the protective boot.Position the upper flap of the partition
panel.Secure the front wiring harness using retaining
clips.Do up the retaining stud.Fit the brake fluid reservoir, tighten
the bolts and connect the electrical connection.Fit the bracket and tighten the bolts.Fit the power steering fluid reservoir
and tighten the bolts.Fit the bracket and tighten the bolt.Secure the fuel pipe using a clamp.Fit the weather strip.Connect the electrical connections.Connect the earth terminal.Close the left wiring sleeve.Secure the relays to the mount.Connect the left headlamp alignment motor
electrical connection.Close the right wiring sleeve.Fit the wiring clip and do up the bolt.Connect the windscreen and headlamp washer
pump electrical connections.Connect the electrical connections for
the horns.Connect the right headlamp alignment motor
electrical connection.Connect the rear wiring electrical connections.Connect the brake light switch electrical
connection.Connect the facia wiring electrical connection.Connect the ignition switch electrical
connection.Connect the electrical connections between
front wiring harness and junction unit / CODE control unit.Fit the junction unit / CODE control unit
mounting and tighten the retaining bolts. - 3340A13 abs central mount - r r - 3340A12 A'B.S. system. - electronic and hydraulic CONTROL
UNIT R.R. - 5530B52 Battery DRIP TRAY/SUPPORT - R.R. - 5530B10 battery - r+r - 7055A18 Windscreen base TRIM - R.R. - 5050B34 windscreen wiper arm/s complete with blade - r+r - 5550C22 l/h or r/h side flasher (one) - r+r
(right
and left)
- 7025A26 bonnet lid opening control - repair - 7025A24 boot lid opening lever - r+r - 7025A34 bonnet lid lock (one) - r+r or repair - 7055A41 RIGHT FRONT GRILLE - R.R.
(left side)
- 7055A43 central front grille - r r