3237672 - rear fuel delivery line - r r

Removing ( Refitting ) Place the car on a ramp.Disconnect the battery negative (-) terminal.

	Name	Connector
-	Battery	A1

1. Open the boot lid, undo the bolts (1a) for the luggage retaining hooks, then remove the cover for the load compartment.  - 7050B18  rear seat arm rest - r+r1. Undo the nuts fixing the protective for the fuel pump and place it at the side. 1. Lift up the cover and disconnect the fuel (supply) pipe (1a) from the pump.  - 3380A44  handbrake/linkage protection - r+rLift up the handbrake lever, loosen the adjustment nut, then lower the lever.Raise the car.1. Disconnect the handbrake cables (1a) from the mounting bracket and from the fixings on the fuel tank.2. Remove the last section of the exhaust pipe (2a) and the heat shield (2b) underneath.Position a hydraulic jack under the rear suspension crossmember and undo the bolts fixing it to the bodyshell, lower the jack and the crossmember as necessary and release the fuel tank.Position a hydraulic jack under the fuel tank, then undo the nuts shown by the arrows and remove the fuel tank support rods. 1. Disconnect the rapid connector connecting the rear section of the fuel supply pipe to the front section.Lower the fuel tank as necessary to release the pipe from the retaining bands on the actual tank, then remove the pipe. Refitting ( Removing ) Position the rear section of the fuel supply pipe and fix it to the retaining bands on the tank.Connect the connector securing the rear section of the fuel pipe to the front section.Raise the hydraulic jack and position the tank, then fix it to the bodyshell using the support rods.Remove the hydraulic jack from under the tank.Fit the heat shields and the end section of the exhaust pipe.Reposition the rear suspension crossmember brining it in contact with the bodyshell through the hydraulic jack; fix it to the bodyshell tightening the fixing bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	REAR CROSS-BEAM	M10	6.2 - 6.8

Remove the hydraulic jack from under the rear suspension crossmember.Connect the handbrake cables to the bands on the tank and the bracket.Lower the vehicle, remove it from the ramp and adjust the handbrake cable.Complete operation 3380A44.Connect the connector for the fuel supply pipe to the pump.Fit the protective cover for the fuel pump.Position the cover for the luggage compartment and secure it using the bolts fixing the luggage retaining hook fixing bolts.Close the boot lid and remove the vehicle from the lift.Connect the negative (-) battery terminal.

	Name	Connector
-	Battery	A1

 - 7050B18  rear seat arm rest - r+r Removing ( Refitting ) Place the car on a ramp.Disconnect the battery negative (-) terminal.

	Name	Connector
-	Battery	A1

1. Open the boot lid, undo the bolts (1a) for the luggage retaining hooks, then remove the load compartment cover.  - 7050B18  rear seat arm rest - r+r1. Undo the nuts fixing the protective cover for the fuel pump and place it at the side. 1. Lift up the cover and disconnect the fuel (supply) pipe (1a) from the pump.  - 3380A44  handbrake/linkage protection - r+rLift up the handbrake lever, loosen the adjustment nut, then lower the lever.Raise the car.1. Disconnect the handbrake cables (1a) from the mounting bracket and from the fixings on the fuel tank.2. Remove the last section of the exhaust pipe (2a) and the heat shield (2b) underneath.Position a hydraulic jack under the rear suspension crossmember and undo the bolts fixing it to the bodyshell, lower the jack and the crossmember as necessary and release the fuel tank.Position a hydraulic jack under the fuel tank, then undo the nuts shown by the arrows and remove the fuel tank support rods. 1. Disconnect the rapid connector securing the rear section of the fuel supply pipe to the front section.Lower the fuel tank as necessary to release the pipe from the retaining bands on the actual tank, then remove the pipe. Refitting ( Removing ) Position the rear section of the fuel supply pipe and fix it to the retaining bands on the tank.Connect the connector securing the rear section of the fuel pipe to the front section.Raise the hydraulic jack and position the tank, then fix it to the bodyshell using the support rods.Remove the hydraulic jack from under the tank.Fit the heat shields and the end section of the exhaust pipe.Reposition the rear suspension crossmember bringing it into contact with the bodyshell through the hydraulic jack; fix it to the bodyshell tightening the fixing bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	REAR CROSS-BEAM	M10	6.2 - 6.8

Remove the hydraulic jack from under the rear suspension crossmember.Connect the handbrake cables to the bands on the tank and to the bracket.Lower the vehicle, remove it from the ramp and adjust the handbrake cable.Complete operation 3380A44.Connect the fuel supply pipe connector to the pump.Fit the protective cover for the fuel pump.Position the cover for the luggage compartment and fix it using the fixing bolts for the luggage retaining hooks.Close the boot lid and remove the vehicle from the lift.Connect the negative (-) battery terminal. - 7050B18  rear seat arm rest - r+r