3237545 - 1056B90 system cable bundle - r + r

Removing ( Refitting ) Disconnect the battery negative terminal.

	Name	Connector
-	Battery	A1

1. Disconnect electrical connections (1a) to the injectors, (1b) to the variable valve timing actuator, (1c) to the air flow meter, (1d) from the air temperature sensor, (1e) to the idle actuator.

	Name	Connector
1a	Injector	N70

	Name	Connector
1b	Timing variator actuator	N76

	Name	Connector
1c	Air flow meter	K41

	Name	Connector
1d	Air temperature sensor	K42

	Name	Connector
1e	Idle actuator	N74

2. Remove the fuel manifold plastic protection. 1. Disconnect the electrical connection to the compressor electromagnet coupling.

	Name	Connector
1	Air conditioning compressor "on" electromagnet	L20

1. Unscrew the retaining bolts and remove the coil cover. 1. Disconnect the electrical connections from the ignition coils.

	Name	Connector
1	Ignition coil	A30

1. Disconnect collars (1a) and remove air intake pipe section (1b) complete with flow meter. 1. Undo the nut (1a) and disconnect the earth lead (1b).

	Name	Connector
1b	Earth on engine	C40

2. Disconnect electrical connections (2a) and (2b) from the thermostat.

	Name	Connector
2a	Engine temperature sensor	K45

	Name	Connector
2b	Coolant temperature sender unit	K35

1. Disconnect electrical connection (1a) from the lambda probe and electrical connection (1b) from the throttle position sensor.

	Name	Connector
1a	Lambda sensor	K40

	Name	Connector
1b	Throttle position sensor	K56

1. Disconnect the throttle cable from the fastening points on the throttle body. 1. Unscrew the bolts securing the wiring channel located beneath the intake manifold. 1. Unscrew bolt (1a), open clip (1b) and release fuel lines (1c). 1. Disconnect electrical connections (1a)- (1b)- (1c)-(1d).

	Name	Connector
1a	Front/engine connection	D4

	Name	Connector
1b	Rpm sensor	K46

	Name	Connector
1c	Timing sensor	K47

	Name	Connector
1d	Detonation sensor - 1	K50

 - 1008C10  power unit upper reaction link r r1. Remove the injector wiring plastic protection. Working from inside the car, remove the plastic protection of the i.e. control unit.1. Disconnect the single connector from the i.e. control unit

	Name	Connector
1	Engine management ECU	M10

 - 4450B10  Front WHEEL (one) - R.R. - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R.1. Disconnect the electrical connection from the activated carbon filter.

	Name	Connector
1	Fuel vapour recovery solenoid	L10

1. Working from the engine bay, raise the pollen filter protection gasket. 1. Remove the pollen filter protection. 1. Unscrew nuts (1a) securing the wiring to the body, then withdraw enging wiring (1b) and remove. Refitting ( Removing ) Pull the engine wiring through the hole on the body until it reaches the i.e. control unit.Connect the connection to the activated carbon filter. - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 4450B10  Front WHEEL (one) - R.R.Connect the single connector to the i.e. control unit.Secure the engine wiring to the body.Refit the pollen filter guard and gasket. - 1008C10  power unit upper reaction link r rConnect the electrical connections.

	Name	Connector
-	Front/engine connection	D4

	Name	Connector
-	Rpm sensor	K46

	Name	Connector
-	Timing sensor	K47

	Name	Connector
-	Detonation sensor - 1	K50

Tighten the connection bracket, do up the clip and secure the fuel lines.Secure the wiring channel beneath the intake manifold.Connect t he accelerator cable to the throttle body.Connect the electrical connection for the Lambda sensor.Connect the electrical connections to the thermostat.

	Name	Connector
-	Engine temperature sensor	K45

	Name	Connector
-	Coolant temperature sender unit	K35

Connect the earth lead.

	Name	Connector
-	Earth on engine	C40

Refit the air intake line section complete with flow meter.Connect the electrical connections to the ignition coils.Refit the coil cover and tighten the bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	IGNITION COIL/REEL COVER/S	M6	0.9

Connect the electrical connection to the compressor electromagnet coupling.Connect the electrical connections.

	Name	Connector
-	Injector	N70

	Name	Connector
-	Timing variator actuator	N76

	Name	Connector
-	Air flow meter	K41

	Name	Connector
-	Air temperature sensor	K42

	Name	Connector
-	Idle actuator	N74

Refit the fuel manifold plastic protection.Connect the battery negative terminal.Remove the vehicle from the ramp. Removing ( Refitting )  - 5530B10  battery - r+rRemove the ignition coil protection.1. Disconnect electrical connections (1a) - (1s), release the retaining collars, then remove the injection wiring from the engine.

	Name	Connector
1a	Injector	N70

	Name	Connector
1b	Ignition coil	A30

	Name	Connector
1c	Air conditioning compressor "on" electromagnet	L20

	Name	Connector
1d	Engine temperature sensor	K45

	Name	Connector
1e	Coolant temperature sender unit	K35

	Name	Connector
1f	Air flow meter	K41

	Name	Connector
1g	Earth on engine	C40

	Name	Connector
1h	Idle actuator	N74

	Name	Connector
1i	Engine management ECU	M10B

	Name	Connector
1l	Front/engine connection	D4

	Name	Connector
1m	Variable geometry control solenoid	L15

	Name	Connector
1n	Detonation sensor - 1	K50

	Name	Connector
1o	Lambda sensor	K40

	Name	Connector
1p	Fuel vapour recovery solenoid	L10

	Name	Connector
1q	Rpm sensor	K46

	Name	Connector
1r	Timing sensor	K47

	Name	Connector
1s	Timing variator actuator	N76

Refitting ( Removing ) Arrange the injection wiring on the engine and connect the electrical connections:Timing variator actuatorTiming sensor.Rpm sensorFuel vapour recovery solenoidLambda probe.Knock sensor - 1.Variable geometry control solenoidFront/engine connectionEngine management control unitIdle actuatorEarth on engine.Air flow meter.Coolant temperature sender unitEngine temperature sensor. Air conditioning compressor electro-magnetIgnition coil.Injector.Check the continuity of the electrical contacts.Refit the ignition coil protection and tighten to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	IGNITION COIL/REEL COVER/S	M6	0.9

 - 5530B10  battery - r+r