4410C10 FRONT SUSPENSION STABILIZER BAR - R+R - CHECK WHEEL GEOMETRY SEPARATELY - Alfa - 156 - eLearn

3238189 - 4410C10 front suspension stabilizer bar - r+r - check wheel geometry separately

) Position the vehicle on the ramp. - 4450B12 front or rear wheels (two) - r+r - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 1076B50 exhaust pipe attachment to engine - r + r Proceed with the removal - 1008A44 rear rigid mount - r r bearing in mind that there is a different set of specific operations for each version. 1. Undo the bolts securing the anti-roll bar to the front suspension crossmember.2. Undo the bolts (2a) and the nuts (2b) fixing the gear lever and handbrake lever mount.3. Undo the bolts fixing the power assisted steering box to the front suspension crossmember.4. Position a hydraulic jack under the crossmember.5. Undo the rear bolt securing the front suspension to the bodyshell.6. Undo the side bolts securing the front suspension to the bodyshell.Lower the hydraulic jack with the front suspension beam as necessary.

1. Undo the nuts (1a) and remove the joints (1b).

Lower the front suspension crossmember further leaving it secured only to the track control arms.1. Remove the anti-roll bar assembly.

Refitting ( Removing

) Place the anti-roll bar assembly back in its housing.Raise the front suspension crossmember as necessary, then fit the joints and secure them tightening the nuts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	FRONT ANTI-ROLL BAR JOINTS	M10	3.8 - 4.7

Fully raise the front suspension beam using the hydaulic jack.1. Tighten the side bolts securing the front suspension crossmember to the bodyshell to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Side bolt	ENGINE OR ROD ANCHORAGE BEAM	M12	(Bodyshell side) 10.8 ÷ 13.2

2. Tighten the rear bolts (2a) and (2b) fixing the crossmember to the bodyshell to torque.

	Fastening	Component	Ø	Value(daNm)
2a	Rear bolts	ENGINE OR ROD ANCHORAGE BEAM	M12	(Bodyshell side) 10.8 ÷ 13.2

	Fastening	Component	Ø	Value(daNm)
2b	Rear bolt	ENGINE OR ROD ANCHORAGE BEAM	M10	(Bodyshell side) 8.1 ÷ 9.9

Remove the hydraulic jack from underneath the front suspension crossmember.3. Tighten the bolts securing the power steering box to the front suspension crossmember to the specified torque.

	Fastening	Component	Ø	Value(daNm)
3	Bolt	POWER STEERING BOX	M14	11.0 - 13.6

4. Tighten the nuts (4a) and bolts (4b) for the gear lever and handbrake lever mounting.5. Tighten the bolts securing the anti-roll bar to the front suspension crossmember to torque.

	Fastening	Component	Ø	Value(daNm)
5	Bolt	FRONT ANTI-ROLL BAR	M8	2.6 - 3.2

Proceed with the refitting - 1008A44 rear rigid mount - r r bearing in mind that there is a different set of specific operations for each version. - 1076B50 exhaust pipe attachment to engine - r + r - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 4450B12 front or rear wheels (two) - r+rRemove the car from the ramps.