2125C70 GEARBOX/BRAKE LEVER MOUNT - R R - Alfa - 156 - eLearn

3237935 - 2125C70 gearbox/brake lever mount - r r

) Position the vehicle on the ramp. - 5530B10 battery - r+r - 5530B52 Battery DRIP TRAY/SUPPORT - R.R.1. Disconnect the gear selector/engagement cables.2. Undo bolts (2a) and remove mounting bracket (2b) complete with gear selector/engagement cables.

1. Remove the gear lever boot.2. Remove the handbrake boot.3. Lift up the handbrake lever (3a) and loosen the nut (3b) tensioning the handbrake cables.

- 1076B50 exhaust pipe attachment to engine - r + r - 1080B62 catalytic converter - r + r1. Disconnect the rigid exhaust pipe section (1b) from flexible mounting (1a).

1. Remove the retainer (1a) and disconnect the handbrake cables (1b).

1. Position a hydraulic jack under the gear lever and handbrake lever support.2. Undo the bolts (2a) and the nuts (2b) fixing the gear lever and handbrake lever support to the bodyshell.3. Lower the hydraulic jack as far as necessary and unscew nut (3a) of gear selection/engagement cable support plate (3b).

1. Competely lower the hydraulic jack and remove the support for the gear lever and handbrake lever.

1. Remove the safety plates (1a) and remove the gear selector/engagement cable mounting brackets (1b).

1. Undo the nuts (1a) and remove the gear lever support (1b), complete with gear selector/engagement cables (1c).

1. Remove the safety plates (1a) and the circlip (1b), then disconnect and remove the gear selector/engagement cables (1c).

1. Remove the gear lever grip (1a) with the tool (1b) positioned as illustrated in the diagram and undo the bolt until it is completely removed.

	Name	Country
1b	Extractor	1.870.668.000

Protect the contact areas between the gear lever knob and the tool to prevent superficial damage using felt, bodywork tape, etc.

2. Remove the spring.3. Fit the reverse gear inhibitor.4. Remove the circlip (4a) and remove the lever (4b).5. Undo the bolts (5a) and separate the gear control rod (5b) from the supports (5c).

Refitting ( Removing

) 1. Fit the gear control rod (1a) on the supports (1b) and secure using the bolts (1c).2. Fit the lever (2a) and fasten it using the circlip (2b).3. Fit the reverse gear inhibitor.4. Fit the spring.5. Place the gear lever knob (5b) back in its housing with the tool (5b) positioned as illustrated in the diagram and adjust the bolt until the fitting it completed.

	Name	Country
5b	Extractor	1.870.668.000

Connect the gear selector/engagement cables and fix them using the circlip and the safety plates. Fit the gear lever support, complete with gear selector/engagement cables and fix them using the nuts.Fit the gear selector/engagement mounting brackets and fix them using the safety plates.Place the gear lever and handbrake lever support back in its housing using the hydraulic jack.Refit the gear selector/engagement cables mount plate and secure it the appropriate nut.Tighten the bolts and nuts securing the gearlever and handbrake lever mount to the body.Remove the hydraulic jack from underneath the gear lever and handbrake lever support.Connect the handbrake cables and secure them using the retainer.Connect the exhaust pipe rigid pipe to the flexible mounting. - 1080B62 catalytic converter - r + r - 1076B50 exhaust pipe attachment to engine - r + r - 3380A04 handbrake - check travelRefit the handbrake boot.Fit the gear lever boot.Refit the bracket complete with gear engagement/selection cables and secure with boltsPosition the gear lever in neutral and move it completely towards the right.1. Loosen the adjustment nut for the gear selector/engagement unit.2. Fit tool A under the gear engagement cable attachment ball.

	Name	Country
2	Spacer	1.860.974.000

3. Connect the gear selector/engagement cables.Tighten the adjustment nut.Remove the spacer.

- 5530B10 battery - r+r - 5530B10 battery - r+rRemove the car from the ramps.