4130B49 RETURN PIPE FROM POWER STEERING CASE TO HEAT EXCHANGER PIPE R R - Alfa - 156 - eLearn

3238141 - 4130B49 return pipe from power steering case to heat exchanger pipe r r

) Position the vehicle on the ramp. Proceed with removal - 4450B12 front or rear wheels (two) - r+r . Proceed with removal - 7055B54 under-engine guard - r r . Proceed with removal - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. . Proceed with removal - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. . Proceed with removal - 7055A43 central front grille - r r . Proceed with removal - 7055A41 RIGHT FRONT GRILLE - R.R. . Proceed with removal - 7210E10 R.R. FRONT BUMPER . Proceed with removal - 1084C40 Air DUCT for engine oil cooling radiator - R.R . . 1. Disconnect the quick-release fitting on the return pipe from power steering box to heat exchanger, heat exchanger side.

Collect the power assisted steering fluid in a suitable container.

2. Undo the nut for the front bracket fastening the supply and return pipes to the power assisted steering system heat exchanger.

1. Undo the nut for the rear bracket fastening the supply and return pipes to the power assisted steering system heat exchanger.

1. Undo the connector (1a) and disconnect the return pipe from power steering box to heat exchanger (1b), power steering box side.2. Release and remove the return pipe from the power assisted steering box to the heat exchanger.

Refitting ( Removing

) 1. Refit the return pipe from power steering box to heat exchanger in its seating.2. Connect the return pipe from power steering box to heat exchanger (2a), power steering box side, and tighten the connector (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	Connector	PIPE FROM POWER STEERING BOX/EXCHANGER	M12	(Power steering box side) 2.7 ÷ 3.3

Tighten the nuts for the brackets fastening the supply and return pipes to the power assisted steering system heat exchanger.Connect the quick-release fitting on the return pipe from power steering box to heat exchanger, heat exchanger side. Proceed with refitting - 1084C40 Air DUCT for engine oil cooling radiator - R.R . . Proceed with refitting - 7210E10 R.R. FRONT BUMPER . Proceed with refitting - 7055A41 RIGHT FRONT GRILLE - R.R. . Proceed with refitting - 7055A43 central front grille - r r . Proceed with refitting - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. . Proceed with refitting - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. . Proceed with refitting - 7055B54 under-engine guard - r r . Proceed with refitting - 4450B12 front or rear wheels (two) - r+r . Fill the power steering circuit with the recommended fluid.

	Type	Component	Name	Qty.
-	Fluid	HYDRAULIC POWER ASSISTED STEERING SYSTEM	TUTELA GI/A	1.3

Fluid for Northern European countries: TUTELA CAR GI/E - ATF DEXRON III.

The table shows the total quantity of fluid present in the power assisted steering circuit.

Bleed the power steering system as described belowWith the front wheels raised off the ground, with the engine switched off turn the steering wheel to full lock, left and right, 4-5 times. Check and, if necessary, top up the fluid level in the reservoir. Remove the car from the ramps.Start the engine and carry out 4 - 5 full steering wheel turn cycles (right and left). Top up the fluid level in the reservoir.