3238144 - 4130B54 return pipe from heat exchanger pipe to power steering fluid resevior r r

Removing ( Refitting ) Position the vehicle on the ramp Proceed with removal  - 1016A10  sound-proofing cover - r + r . Proceed with removal  - 4450B12  front or rear wheels (two) - r+r . Proceed with removal  - 7055B54  under-engine guard - r r . Proceed with removal  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. . Proceed with removal  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. . Proceed with removal  - 7055A43  central front grille - r r . Proceed with removal  - 7055A41  RIGHT FRONT GRILLE - R.R. . Proceed with removal  - 7210E10  R.R. FRONT BUMPER . Proceed with removal  - 1084C40  Air DUCT for engine oil cooling radiator - R.R . . 1. Disconnect the rapid attachment coupling from the return pipe from the heat exchanger to the power steering fluid reservoir, heat exchanger side.

Collect the power assisted steering fluid in a suitable container.

2. Undo the nut for the front bracket fastening the supply and return pipes to the power assisted steering system heat exchanger. 1. Undo the nut for the rear bracket fastening the supply and return pipes to the power assisted steering system heat exchanger. 1. Disconnect the rapid attachment coupling from the return pipe from the heat exchanger to the power steering fluid reservoir, reservoir side. 1. Position a hydraulic jack under the rigid power unit support, timing side. 2. Undo the bolt securing timing side rigid engine support to the flexible mounting. Lower the power unit, as necessary, using the hydraulic jack to facilitate the removal of the pipe in question.3. Release and remove the return pipe from the heat exchanger to the power assisted steering fluid reservoir. Refitting ( Removing ) Refit in its seating the return pipe from the heat exchanger to the power steering fluid reservoir.Place the power unit back in its housing using the hydraulic jack.Tighten the bolt securing timing side rigid engine support to the flexible mounting to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	-	-	-	-

Remove the hydraulic jack under the rigid power unit support, timing side.Connect the rapid attachment coupling on the return pipe from the heat exchanger to the power steering fluid reservoir, reservoir side.Tighten the nuts for the brackets fastening the supply and return pipes to the power assisted steering system heat exchanger.Connect the rapid attachment coupling on the return pipe from the heat exchanger to the power steering fluid reservoir, heat exchanger side. Proceed with refitting  - 1084C40  Air DUCT for engine oil cooling radiator - R.R . . Proceed with refitting  - 7210E10  R.R. FRONT BUMPER . Proceed with refitting  - 7055A41  RIGHT FRONT GRILLE - R.R. . Proceed with refitting  - 7055A43  central front grille - r r . Proceed with refitting  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. . Proceed with refitting  - 7055B64  Engine compartment DUST shield in front wheel arch (one), left or right - R.R. . Proceed with refitting  - 7055B54  under-engine guard - r r . Proceed with refitting  - 4450B12  front or rear wheels (two) - r+r . Fill the power steering circuit with the recommended fluid.

	Type	Component	Name	Qty.
-	Fluid	HYDRAULIC POWER ASSISTED STEERING SYSTEM	TUTELA GI/A	1.3

Fluid for Northern European countries: TUTELA CAR GI/E - ATF DEXRON III.

The table shows the total quantity of fluid present in the power assisted steering circuit.

Bleed the power steering system as described belowWith the front wheels raised off the ground, with the engine switched off turn the steering wheel to full lock, left and right, 4-5 times. Check and, if necessary, top up the fluid level in the reservoir. Remove the car from the ramps.Start the engine and carry out 4 - 5 full steering wheel turn cycles (right and left). Top up the fluid level in the reservoir. Proceed with refitting  - 1016A10  sound-proofing cover - r + r .