3237469 - 1020A20 crank case oil sump - r + r clean seals for sealant application

 - 1092G10  single engine belt r r - 1092A12  crankshaft pulley - r+r for versions with air conditioner - 1092G20  engine component single belt fixed tensioner - one - r + r - 1032D12  timing system protective cover(s) - r + r  - 1032D12  timing system protective cover(s) - r + r - 1092G20  engine component single belt fixed tensioner - one - r + r - 1092A12  crankshaft pulley - r+r for versions with air conditioner - 1092G10  single engine belt r r Removing ( Refitting )  - 1076B50  exhaust pipe attachment to engine - r + r - 1084A16  oil dip stick pipe - r r1. Undo the bolts (1a) and remove the protection (1b) for the fluid return pipe from to the turbocharger.2. Disconnect the fluid return pipe from the turbocharger from the crankcase sump. 1. Disconnect the condensed oil return pipe from the oil vapour separator from the crankcase sump.2. Undo the drain plug and drain the engine oil.

Collect the engine oil in a suitable container.

3. Undo the bolt connecting the oil sump to the intermediate shaft support. 1. Undo the front and rear bolts (1a) for the crankcase sump using the spanner (1b).

	Name	Country
1b	Key	1.822.145.000

2. Undo the side bolts (2a) for the crankcase sump using the spanner (2b).

	Name	Country
2b	Key	1.822.144.000

3. Lower the crankcase sump, as necessary, and undo the bolts for the engine oil intake.

To loosen the sump from the crankcase, apply gentle blows using a resin hammer, then use a screwdriver for leverage on the special projections at the side of the crankcase sump.

4. Remove the crankcase sump (4a) together with the engine oil inlet (4b). Refitting ( Removing ) Apply the recommended sealant to the entire perimeter of the crankcase sump.

	Type	Component	Name	Qty.
-	Silicon sealant	OIL SUMP	-	-

1. Fit the crankcase sump (1a) together with the engine oil intake (1b).2. Tighten the bolts for the engine oil intake.3. Tighten the side bolts (3a) for the crankcase sump to the recommended torque using the spanner (3b).

	Fastening	Component	Ø	Value(daNm)
3a	Side bolts	OIL SUMP	M6	(Crankcase side) 0.7 ÷ 0.9

	Name	Country
3b	Key	1.822.144.000

4. Tighten the front and rear bolts (4a) for the crankcase sump to the recommended torque using the spanner (4b).

	Fastening	Component	Ø	Value(daNm)
4a	Front and rear bolt	OIL SUMP	M8	(Crankcase side) 2.1 ÷ 2.6

	Name	Country
4b	Key	1.822.145.000

1. Tighten the bolt connecting the crankcase sump to the intermediate shaft support to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	OIL SUMP	M8	2.1 - 2.6

2. Tighten the crankcase sump drain plug to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2	Drain plug	OIL SUMP	M18	1.7 - 2.1

3. Connect the condensation oil return pipe from the oil vapour separator to the crankcase sump. Connect the oil return pipe from the turbocharger to the crankcase sump.Fit the protection for the oil return pipe from the turbocharger. - 1084A16  oil dip stick pipe - r r - 1076B50  exhaust pipe attachment to engine - r + rRefill the engine lubrication circuit using oil.

	Type	Component	Name	Qty.
-	Oli [l]	ENGINE LUBRICATION CIRCUIT	SELENIA TURBODIESEL	5.5

For the optimum operation of the engine in particularly harsh climatic conditions (temperatures below -15° C), use the recommended oil for the engine lubrication circuit.

	Type	Component	Name	Qty.
-	Oli [l]	ENGINE LUBRICATION CIRCUIT	SELENIA WR DIESEL	5.5