1032B14 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT VERSIONS WITH AIR CONDITIONER - Alfa - 156 - eLearn

3237490 - 1032B14 toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner

- 1092E10 counter-rotating shaft drive toothed belt - r + r 1. Fit the crankshaft rotation tool on the counter-balance shaft belt drive pulley.

	Name	Country
1	Flange	1.820.618.000

- 1092E10 counter-rotating shaft drive toothed belt - r + r

Removing ( Refitting

) Position the vehicle on the ramp. - 4450B10 Front WHEEL (one) - R.R. - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 1092G10 single engine belt r r - 1092A12 crankshaft pulley - r+r for versions with air conditioner - 1032D12 timing system protective cover(s) - r + r - 1008C10 power unit upper reaction link r r - 1016A10 sound-proofing cover - r + r . - 1008C14 engine link bracket - r rRemove the tool fitted previously.

	Name	Country
-	Counter-torque	1.820.630.000

1. Adjust the timing belt drive pulley and rotate the crankshaft until the timing marks line up (cylinder no. 1 at T.D.C.).2. Check that the locating dowel on the timing belt drive pulley is facing downwards.3. Slacken the timing belt tensioner nut.4. Remove the timing drive belt.

Refitting ( Removing

) 1. Remove the bolt for the oil pump shown.Temporarily fit the timing drive belt on the drive pulley.

Instructions for correct checking of toothed timing belt condition:

Check that the timing belt does not show signs of loose threads or cracks.
Check for 'black dust' along the entire length of the belt, on the toothed wheels, the shields, etc.
Visually inspect the belt teeth for check for any wear of the protective outer fabric.
If one or more of the above conditions indicating excess wear is found, replace the timing drive belt.
The entire length of the belt should be inspected.

2. Fit the tool (2a) and secure it with gauged bolts (2b)

To allow the engagement of the locating dowel on the timing drive belt drive pulley in the opening in the tool, rotate the crankshaft using small movements.

	Name	Country
2a	Template	1.860.905.000

	Name	Country
2b	Calibrated screw	1.860.905.010

1. Check that the timing references coincide.2. Completely fit the timing belt.3. Use a screwdriver to lever in the hole (3a) until the reference on the tensioner (3b) lines up with the reference hole (3c) and, in this position, tighten the belt tensioner nut (3d) to torque.

	Fastening	Component	Ø	Value(daNm)
3d	Nut	MOBILE TIMING TENSIONER	M10	4.2 ÷ 5.2

4. Remove the tools.

	Name	Country
4	Template	1.860.905.000

	Name	Country
4	Calibrated screw	1.860.905.010

Tighten the bolt on the oil pump removed previouslyRotate the crankshaft through two revolutions.Recheck that the timing references and the tensioning references on the timing belt tensioner are aligned.

- 1008C14 engine link bracket - r r - 1016A10 sound-proofing cover - r + r . - 1008C10 power unit upper reaction link r r - 1032D12 timing system protective cover(s) - r + r - 1092A12 crankshaft pulley - r+r for versions with air conditioner - 1092G10 single engine belt r r - 7055B64 Engine compartment DUST shield in front wheel arch (one), left or right - R.R. - 4450B10 Front WHEEL (one) - R.R.Remove the car from the ramp.