7035A18 WINDSCREEN GLASS R R INCLUDING CLEANING OF HOUSING - Alfa - 156 - eLearn

3238775 - 7035A18 windscreen glass r r including cleaning of housing

) - 7065C68 rear view mirror - r+r - 7025A14 Bonnet LID - R.R. - 5050B34 windscreen wiper arm/s complete with blade - r+r - 7055A18 Windscreen base TRIM - R.R.Protect the facia and wings using covers.1. Remove the rain gutters in the area of the front pillars.2. Remove the supports from the windscreen.3. Remove the perimetral seal of the windscreen.4. Remove the windscreen side seals.5. Apply adhesive tape to protect the edges of the bodywork, in the areas shown.

1. Using a vibrating knife (1a) and blade (1b), cut the sealant along the bottom of the windscreen.Work from the outside of the vehicle.

	Name	Country
1a	Vibrating knife	1.823.011.000

	Name	Country
1b	Blade	1.823.019.000

2. Fit the blade (2a) and cut the sealant on the other sides of the windscreen.Work from the outside of the vehicle.

	Name	Country
2a	Blade	1.823.022.000

3. Fit the suction handles to the windscreen and, with the assistance of a second operator, remove the windscreen and rest it on a supporting stand.

Refitting ( Removing

) 1. Using the vibrating knife (1a) and blade (1b), cut and level the sealant in the windscreen housing so that the thickness left is between 0.25 and 1 mm without scratching the paint.The sealant left in the frame will act as a backing for the new bond.

	Name	Country
1a	Vibrating knife	1.823.011.000

	Name	Country
1b	Blade	1.823.010.000

2. Clean the windscreen seating carefully with compressed air and degrease thoroughly using heptane.Touch up the paintwork if necessary.3. Refit the side seals on both sides of the windscreen.

Check that the window is undamaged.1. Degrease the screen-printed edge of the new windscreen using heptane.2. Using the swab (2a) supplied in the kit, apply the glass adhesion promoter (primer) (2b) on the printed perimeter.Wait for 15 minutes before carrying out the next operation to give the primer thinner time to evaporate.

1. Fit the seal around the perimeter of the windscreen.Avoid touching the treated area with the hands.Use a new seal.2. Test fit the windscreen and centre it perfectly, using the supports.3. After centering the windscreen, mark the position of the windscreen and the housing with strips of adhesive tape.4. Cut the strips of adhesive tape and remove the windscreen.5. Use an air gun to extrude a bead of sealant as evenly as possible along the perimeter of the windscreen.Begin applying the sealant from the middle of the lower edge and continue without breaks around the entire edge of the window.

1. With the assistance of a second operator, fit the windscreen in its seating immediately after applying the sealant and bed it in place.2. Fit the belt (2a) as shown in the figure and tension it so as to apply even pressure over the entire windscreen, in order to ensure a correct match between windscreen (2b), sealant (2c) and windscreen frame (2d).

Before refitting the car's exterior elements, check that there are no penetration points.Apply soapy water using a sponge along the outer perimeter and blow through with compressed air from the inside to identify any penetration.Fit the perimeter seal.Fit the rain gutters in the area of the front pillars. - 7055A18 Windscreen base TRIM - R.R. - 5050B34 windscreen wiper arm/s complete with blade - r+r - 7025A14 Bonnet LID - R.R. - 7065C68 rear view mirror - r+r

Do not move the car until the time specified by the sealant manufacturer has elapsed.