1020D17 ENGIND FRONT COVER - R R - Alfa - 156 - eLearn

3239088 - 1020D17 engind front cover - r r

) 1. Fit the tool.

	Name	Country
1	Counter-torque	1.820.624.000

1. Slacken the bolt securing the timing belt pulley.Remove the tool.

	Name	Country
-	Counter-torque	1.820.624.000

1. Adjust the automatic belt tensioner with a wrench to slacken the tension of the single drive belt.2. Remove the single drive belt.3. Undo the bolt (3a) and remove the fixed belt tensioner (3b) for the engine components single belt.

1. Undo the bolts (1a) and remove the upper timing belt guard (1b).2. Undo the bolts (2a) and remove the single drive belt drive pulley (2b).3. Loosen the timing belt tensioner nut.4. Remove the timing belt.

1. Completely undo the bolt (1a) loosened previously and remove the timing drive belt pulley (1b).2. Undo the bolts (2a) and remove the timing side rigid power unit support (2b).3. Disconnect the water outlet pipe from the water-oil heat exchanger.4. Disconnect the water inlet pipe to the water-oil heat exchanger.

Rotate the engine through 180° on the overhauling stand.1. Undo the bolt connecting the crankcase sump to the intermediate shaft support.2. Undo the front and rear bolts (2a) for the crankcase sump using the tool (2b).

	Name	Country
2b	Key	1.822.145.000

3. Undo he side bolts (3a) for the crankcase sump using the tool (3b).

	Name	Country
3b	Key	1.822.144.000

4. Remove the crankcase sump.

To release the sump, tap it gently with a wooden or resin hammer, then use a screwdriver to lever against the specific projections on the sides of the sump.

1. Undo the bolts (1a) and remove the oil pump (1b) complete with intake duct (1c), water-oil heat exchanger (1d) and oil filter (1e).2. Remove the seal.Remove the crankshaft front oil seal.

Refitting ( Removing

) Fit the oil pump complete with intake duct, water-oil heat exchanger, oil filter and a new gasket and tighten the bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CRANKSHAFT FRONT COVER	M6	0.6 - 0.8

1. Fit a new crankshaft front oil seal (1a) using the tool (1b).

	Name	Country
1b	Fitting tool	1.821.247.000

Apply sealant to the entire perimeter of the crankcase sump.

	Type	Component	Name	Qty.
-	Silicon sealant	OIL SUMP	-	-

Fit the crankcase sump.Tighten the side bolts for the crankcase sump to torque using the tool.

	Fastening	Component	Ø	Value(daNm)
-	Side bolts	OIL SUMP	M6	0.7 ÷ 0.9

	Name	Country
-	Key	1.822.144.000

Tighten the front and rear bolts for the crankcase sump to torque using the tool.

	Fastening	Component	Ø	Value(daNm)
-	Front and rear bolt	OIL SUMP	M8	2.1 ÷ 2.6

	Name	Country
-	Key	1.822.145.000

Tighten the bolt securing the oil sump to the intermediate shaft support.Rotate the engine through 180° on the overhauling stand.Connect the water inlet pipe to the water-oil heat exchanger and fix it using the clip.Tighten the connector on the water outlet pipe from the water-oil heat exchanger.Fit the power unit support, timing gear side, and fix it using the bolts.Fit the timing belt drive pulley and fix it using the bolt, without tightening it.1. Disconnect the electrical connections from the ignition coils.

	Name	Connector
1	Ignition coil	A30

2. Disconnect the earth lead from the cylinder head.3. Disconnect the high-tension leads (3a) from the spark plugs using the tool (3b).

	Name	Country
3b	Pliers	1.820.636.000

Undo the bolts and remove the bracket complete with ignition coils and high-tension leads.Undo the bolts and remove the rocker cover complete with gasket.1. Slacken the bolt (1a) on the exhaust side camshaft pulley, using the tools (1b) for counter-torque.

	Name	Country
1b	Counter-torque	1.822.146.000

	Name	Country
1b	Counter-torque	1.822.156.000

2. Slacken the bolts (2a) on the inlet side camshaft pulley, using the tool (2b) for counter-torque.

	Name	Country
2b	Counter-torque	1.822.155.000

Fit the timing belt.Apply maximum tension to the timing belt using the tool.

	Name	Country
-	Key	1.822.149.000

Tighten the belt tensioner nut to torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	MOBILE TIMING TENSIONER	M8	2.1 - 2.6

Tighten the bolts (3a) of the inlet side camshaft pulley, using the tool (3b) for counter-torque.

	Name	Country
-	Counter-torque	1.822.155.000

Tighten to torque the bolt (4a) on the exhaust side camshaft pulley, using the tools (4b) for counter-torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	TIMING GEAR DRIVEN PULLEYS	M12	10.0 - 12.4

	Name	Country
-	Counter-torque	1.822.146.000

	Name	Country
-	Counter-torque	1.822.156.000

Fit the camshaft caps removed previously and tighten the bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CAMSHAFT CAPS	M7	1.2 - 1.6

Rotate the crankshaft through two revolutions.Slacken the timing belt tensioner nut.5. Line up the moving reference (5a) on the timing belt tensioner with the reference hole (5b) using the tool (5c).

	Name	Country
5c	Key	1.822.149.000

Tighten the timing belt tensioner nut to torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	MOBILE TIMING TENSIONER	M8	2.1 - 2.6

Remove the tool complete with dial gauge.

	Name	Country
-	Extension	1.825.013.000

Fit the spark plug for cylinder no. 1. Fit the rocker cover complete with gasket and fix it using the bolts.Fit the bracket complete with ignition coils and high-tension cables and fix it using the boltsConnect the high-tension leads to the spark plugs.Connect the earth lead to the cylinder head.Connect the electrical connections to the ignition coils.

	Name	Connector
-	Ignition coil	A30

Fit the upper timing belt guard and fix it using the bolts.Fit the single drive belt pulley and tighten the bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CRANKSHAFT PULLEY	M8	2.4 - 2.9

Fit the fixed single drive belt tensioner and fix it with its bolt.Fit the auxiliary components drive belt, using a spanner to lever on the automatic belt tensioner.Fit the tool.

	Name	Country
-	Counter-torque	1.820.624.000

Tighten the timing belt pulley bolt to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt with left hand thread	TOOTHED DRIVE PULLEY	M16	34.0 ÷ 37.8

Remove the tool.

	Name	Country
-	Counter-torque	1.820.624.000