3237522 - 1040B36 rear fuel delivery line - r r

Lower the left-hand squab.1. Undo the bolts securing the squabs to the floor. 1. Unscrew the bolt securing the end of the rear central seat belt (only for version with central inertia reel seat belt). Lower the right squab.1. Undo the bolts securing the squab to the floor.2. Move the squab assembly forward and rest on the seat. 1. Release the retaining buttons using the special tool.

	Name	Country
1	Scraper blade	1.823.015.000

2. Move the trim backward. 1. Undo the bolts.2. Remove the fuel pump cover.3. Remove the safety clip by pushing back with a screwdriver. 4. Raise retainer (4a) using a screwdriver and disconnect electrical connection (4b).

	Name	Connector
4b	Fuel pump and sender unit	N40

5. Undo the bolts.6. Unscrew the nuts.7. Remove the plate. 1. Disconnect the quick-release connector of the rear fuel supply pipe, fuel pump side. Remove the handbrake boot.1. Lift up the handbrake lever (1a), loosen the adjustment nut (1b), then lower the lever. 1. Disconnect the handbrake cables (1a) from the mounting bracket (1b) and from the intermediate fixings (1c). 1. Position a hydraulic jack under the rear suspension crossmember. 2. Undo the bolts (2a) and lower the rear suspension crossmember (2b), as necessary, using the hydraulic jack. 1. Position a hydraulic jack under the fuel tank.2. Undo the bolts (2a) and remove the fuel tank support belts (2b). 3. Disconnect the rapid attachment for the rear fuel supply pipe, front fuel supply pipe side. 1. Lower the fuel tank as necessary to remove the rear fuel supply pipe. Refitting ( Removing ) Place the rear fuel supply pipe back in its housing and fix it to the bands on the tank. Connect the rapid attachment for the rear fuel supply pipe, front fuel supply pipe side. Place the fuel tank support belts back in their housings and secure them using the bolts. Remove the hydraulic jack from under the tank.Place the rear suspension crossmember back in its housing using the hydraulic jack and fix it tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	REAR CROSS-BEAM	M10	(Bodyshell side) 6.2 ÷ 6.8

Remove the hydraulic jack from under the rear suspension crossmember. Connect the handbrake cables to the mounting bracket and to the intermediate fixings. Proceed with refitting  - 3380A04  handbrake - check travel . Place the handbrake boot back in its housing. Raise the right squab.1. Fit the end of the centre rear seat belt in position and secure by tightening the bolt to the recommended torque (only for the version with seat belt with winder).

	Fastening	Component	Ø	Value(daNm)
1	-	REAR SEAT BELT END.	-	4.0

Lower the left-hand squab.1. Tighten the bolts securing the squabs to the floor to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	REAR SEAT ASSEMBLY	M8	2.4

Raise the left-hand squab.1. Tighten the front central bolts securing the squabs to the floor to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	REAR SEAT ASSEMBLY	M8	2.4

Check that the engagement device is working properly. If necessary, adjust the striker  - 7050A45  STRIKER FOR ATTACHMENT/RELEASE DEVICE for .one( SPLIT rear), seat BACKREST left or right - R.R. . Lower the rear cushion. Proceed with refitting  - 7040B10  load platform (luggage platform) trim - r+r . Proceed with refitting  - 7040B28  PET transport PROTECTION and load carrying compartment COVER COMBINATION BLIND - R.R. .