3237862 - 1060G90 diesel injection wiring harness - r r

Removing ( Refitting ) Position the vehicle on the ramp. Proceed with removal  - 5530B10  battery - r+r . Proceed with removal  - 1016A10  sound-proofing cover - r + r . Proceed with removal  - 7055B54  under-engine guard - r r . Proceed with removal  - 1076B70  exhaust pipe between pre-catalytic converter and catalytic converter - r r . 1. Disconnect the electrical connection from the engine oil pressure warning light switch.

NameConnector
1Engine oil pressure sensor  K30 
2. Disconnect the electrical connection for the engine oil level sensor.

NameConnector
2Engine oil level sensor  K32 
3. Disconnect the electrical connection for the rpm sensor.

NameConnector
3Rpm sensor  K46 
1. Disconnect the earth lead from the alternator.

NameConnector
1Alternator  A10 
2. Disconnect the earth lead from the starter motor.

NameConnector
2Starter' motor  A20 
1. Disconnect the electrical connection from the solenoid on the vacuum tank.

NameConnector
1Butterfly casing solenoid valve  L62 
1. Disconnect the electrical connection from the air flow meter.

NameConnector
1Air flow meter  K41 
2. Disconnect the electrical connection from the engine coolant temperature sensor and release the wiring from the bands.

NameConnector
2Engine temperature sender unit  K36 
1. Disconnect the electrical connection from the cam angle sensor.

NameConnector
1Timing sensor  K47 
2. Disconnect the electrical connection for the air conditioning compressor.

NameConnector
2Air conditioning compressor "on" electromagnet  L20 
1. Disconnect the electrical connections from the injectors.

NameConnector
1Injector  N70 
Release the electrical wiring from the band on the timing cover. 2. Undo the bolts fastening the cable duct and move the electrical wiring aside.
1. Disconnect the electrical connections from the heater plugs.

NameConnector
1Heater plug  A40 
2. Disconnect the electrical connection from the fuel pressure sensor.

NameConnector
2Fuel pressure sensor  K83 
3. Disconnect the electrical connection from the excess pressure sensor.

NameConnector
3Turbocharging sensor  K82 
4. Disconnect the electrical connection from the E.G.R. valve.

NameConnector
4EGR solenoid  L30 
1. Disconnect the electrical connection from the fuel pressure regulator.

NameConnector
1Fuel pressure regulator  N77 
2. Disconnect the rapid attachment for the fuel return pipe to the tank, fuel return manifold pipe side. 3. Disconnect the front engine coupling.

NameConnector
3Front/engine connection  D4 
1. Undo the nuts (1a) and lift up the heater plugs control unit (1b) as much as necessary. 2. Disconnect the electrical connection from the pre-heating control unit.

NameConnector
2Plug preheating control unit  M15 
1. Connect the electrical connections to the diesel electronic injection control unit.

NameConnector
1Engine management ECU  M10A 
Release the spark plug cable loom from the securing bands and remove it. Refitting ( Removing ) Place the cable loom back in its housing and fix it using the bands.Connect the electrical connection to the diesel electronic injection control unit. Connect the rapid attachment for the fuel return pipe to the tank, fuel return manifold pipe side. Connect the front engine coupling.Connect the electrical connection to the pre-heating control unit.Place the heater plugs control unit back in its housing and secure it using the nuts. Connect the electrical connection to the fuel pressure regulator.Connect the electrical connection to the E.G.R. valve.Connect the electrical connection to the excess pressure sensor. Connect the electrical connection to the fuel pressure sensor.Connect the electrical connections to the heater plugs. Tighten the cable duct fixing bolts.Fasten the electrical wiring to the band on the timing cover. Connect the electrical connection to the air conditioner compressor.Connect the electrical connection to the cam angle sensorConnect the electrical connections to the injectors.Connect the electrical connection to the engine coolant temperature sensor and fasten the wiring to the bands. Connect the electrical connection to the air flow meter.Connect the electrical connection to the solenoid on the vacuum tank.Connect the earth lead to the starter motor.Connect the earth lead to the alternator.Connect the electrical connection for the rpm sensor.Connect the electrical connection for the engine oil level sensor.Connect the electrical connection to the engine oil pressure warning light switch. Proceed with refitting  - 1076B70  exhaust pipe between pre-catalytic converter and catalytic converter - r r . Proceed with refitting  - 7055B54  under-engine guard - r r . Proceed with refitting  - 1016A10  sound-proofing cover - r + r . Proceed with refitting  - 5530B10  battery - r+r . Remove the car from the ramps.