3237935 - 2125C70 gearbox/brake lever mount - r r

Removing ( Refitting ) Position the vehicle on the ramp Proceed with removal  - 1016A10  sound-proofing cover - r + r . Proceed with removal  - 5530B10  battery - r+r . Proceed with removal  - 5530B52  Battery DRIP TRAY/SUPPORT - R.R. . 1. Disconnect the gear selector cable.2. Disconnect the gear engagement cable.3. Remove the retaining clips (3a) and release the gear selector and engagement cables (3b) from the mounting bracket.
1. Remove the gear lever boot.2. Remove the handbrake boot.3. Lift up the handbrake lever (3a) and loosen the nut (3b) tensioning the handbrake cables.
Proceed with removal  - 7055B54  under-engine guard - r r . Proceed with removal  - 1076B70  exhaust pipe between pre-catalytic converter and catalytic converter - r r . Proceed with removal  - 1080B62  catalytic converter - r + r . 1. Remove the retainer (1a) and disconnect the handbrake cables (1b).
1. Position a hydraulic jack under the gear lever and handbrake lever support.2. Undo the bolts (2a) and the nuts (2b) fixing the gear lever and handbrake lever support to the bodyshell.3. Lower the hydraulic jack as far as necessary and unscew nut (3a) of gear selection and engagement cable support plate (3b).
1. Competely lower the hydraulic jack and remove the support for the gear lever and handbrake lever.
1. At the bench, undo the nuts (1a) and remove the gear lever support (1b), complete with gear selector/engagement cables (1c).
1. Remove the retaining clips (1a) and the circlip (1b), then disconnect the gear selection and engagement cables (1c).
1. Remove the gear lever grip (1a) with the tool (1b) positioned as illustrated in the diagram and undo the bolt until it is completely removed.
Protect the contact areas between the gear lever knob and the tool to prevent superficial damage using felt, bodywork tape, etc.

NameCountry
1bExtractor1.870.668.000
2. Remove the spring.3. Fit the reverse gear inhibitor.4. Remove the circlip (4a) and remove the lever (4b).5. Undo the bolts (5a) and separate the gear control rod (5b) from the supports (5c).
Refitting ( Removing ) 1. Fit the gear control rod (1a) on the supports (1b) and secure using the bolts (1c).2. Place the lever (2a) in its housing and secure it using the circlip (2b).3. Place the reverse gear inhibitor back in its housing.4. Place the spring back in its housing.5. Place the gear lever knob (5b) back in its housing with the tool (5b) positioned as illustrated in the diagram and adjust the bolt until the fitting it completed.

NameCountry
5bExtractor1.870.668.000
Connect the gear selector and engagement cables and secure them using the circlip and the retaining clips.Place the gear lever mounting complete with gear selector and engagement cables back in its housing and secure it using the nuts.Place the gear lever and handbrake lever support back in its housing using the hydraulic jack.Place the gear selector and engagement cables mounting plate back in its housing and secure it using the nut.Tighten the bolts and nuts securing the gearlever and handbrake lever mount to the body.Remove the hydraulic jack from underneath the gear lever and handbrake lever support.Connect the handbrake cables and secure them using the safety clip.Place the boot in its seat Proceed with refitting  - 1080B62  catalytic converter - r + r . Proceed with refitting  - 1076B70  exhaust pipe between pre-catalytic converter and catalytic converter - r r . Proceed with refitting  - 7055B54  under-engine guard - r r .  - 3380A04  handbrake - check travel . IF THE GEAR SELECTOR CABLE IS BEING REUSED AND DOES NOT NEED ADJUSTING, PROCEED AS FOLLOWS.Connect the end of the gear selector cable.Fasten the gear selector cable to the mounting bracket using the retaining clip.Connect the end of the gear engagement cable.Fasten the gear engagement cable to the mounting bracket using the retaining clip.Place the gear lever boot back in its housing. Proceed with refitting  - 5530B52  Battery DRIP TRAY/SUPPORT - R.R. . Proceed with refitting  - 5530B10  battery - r+r . Proceed with refitting  - 1016A10  sound-proofing cover - r + r . Remove the car from the ramps.IF THE GEAR SELECTOR CABLE IS BEING REPLACED OR THE CURRENT ONE IS BEING ADJUSTED, PROCEED AS FOLLOWS.1. Working in the engine compartment, lift up the selector unit until opening (1a) is aligned with opening (1b), then insert a 5 mm diameter pin (1c) and lock the assembly in this position.
Place the gear lever in neutral in the end of travel position against the left side of the housing (driver's side), then lock it in this position.Working in the engine compartment, connect the end of the gear selector cable and lock the adjustment device.Fasten the gear selector cable to the mounting bracket using the retaining clip. Connect the end of the gear engagement cable.Fasten the gear engagement cable to the mounting bracket using the retaining clip.Remove the pin and the tool used for locking the gear lever and check the selection and engagement of all the gears.Place the gear lever boot back in its housing. Proceed with refitting  - 5530B52  Battery DRIP TRAY/SUPPORT - R.R. Proceed with refitting  - 5530B10  battery - r+r Proceed with refitting  - 1016A10  sound-proofing cover - r + rRemove the car from the ramps.