125000877 - 1008A44 REAR RIGID MOUNT - R R

Removing ( Refitting ) Position the vehicle on a lift.Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal.

	Description	Connector
-	Battery	See A1B BATTERY ( BATTERY NEGATIVE )

Drain the air conditioning refrigerant circuit    Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE.Proceed with the removal    Op. 4450B04 RIGHT FRONT WHEEL R R.Proceed with the removal    Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with the removal    Op. 5040A20 AIR CONDITIONER COMPRESSOR - R+R - INCLUDES FLUID LEVEL CHECK AND TOP UP IF NECESSARY.Proceed with the removal    Op. 5040A26 COMPRESSOR MOUNT - R R.Proceed with the removal    Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R.Proceed with the removal    Op. 1076A48 CATALYTIC CONVERTER HEAT SHIELD - R R.Proceed with the removal    Op. 1080B62 CATALYTIC CONVERTER - R + R.1. Undo the bolt fixing the rigid pipe mounting collar for the exhaust pipe between the catalytic converter and the silencer to the bracket.2. Loosen the collar (2a) and remove the rigid pipe for the exhaust pipe between the catalytic converter and the silencer (2b).3. Remove the seal. 1. Undo the bolt (1a) and the nut (1b) and remove the exhaust pipe mounting (1c). 1. Undo the bolts (1a) and remove the heat shield (1b). Position a hydraulic jack beneath the engine.1. Undo the bolt (1a) and the nut (1b) and remove the reinforcement rod (1c). 1. Undo the bolts (1a) and remove the rigid power unit rear support (1b). Refitting ( Removing ) 1. Place the power unit rigid rear support (1a) in its housing and secure it tightening the bolts (1b, (1c) and (1d) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	RIGID REAR SUPPORT POWER UNIT	M12	(Gearbox side) 7.2 - 8.8

	Fastening	Component	Ø	Value(daNm)
1c	Bolt	RIGID REAR SUPPORT POWER UNIT	M12	(Engine crankcase side) 6.8 - 8.3

	Fastening	Component	Ø	Value(daNm)
1d	-	-	-	-

1. Place the reinforcement rod (1a) in its housing and fasten it tightening the bolt (1b) and the nut (1c) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	REINFORCEMENT ROD FOR POWER UNIT RIGID REAR SUPPORT	M12

	Fastening	Component	Ø	Value(daNm)
1c	-	-	-	-

Remove the hydraulic jack from beneath the engine.Place the heat shield back in its housing and secure it using the bolts.1. Place the exhaust pipe mounting (1a) in its housing and fasten it tightening the bolt (1b) and the nut (1c) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	EXHAUST PIPE RIGID MOUNT	M8	2.3 ÷ 2.8

	Fastening	Component	Ø	Value(daNm)
1c	Nut	EXHAUST PIPE RIGID MOUNT	M8

1. Place the rigid pipe for the exhaust pipe between the catalytic converter and the silencer (1a) complete with gasket (1b) back in its housing and secure it to the front exhaust silencer tightening the bolts (1c) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1c	Bolt	RIGID EXHAUST PIPE	M8

2. Tighten the bolt fixing the rigid pipe mounting collar for the exhaust pipe between the catalytic converter and the silencer to the bracket. Proceed with the refitting    Op. 1080B62 CATALYTIC CONVERTER - R + R.Proceed with the refitting    Op. 1076A48 CATALYTIC CONVERTER HEAT SHIELD - R R.Proceed with the refitting    Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R.Proceed with the refitting    Op. 5040A26 COMPRESSOR MOUNT - R R.Proceed with the refitting    Op. 5040A20 AIR CONDITIONER COMPRESSOR - R+R - INCLUDES FLUID LEVEL CHECK AND TOP UP IF NECESSARY.Proceed with the refitting    Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with the refitting    Op. 4450B04 RIGHT FRONT WHEEL R R.Refill the air conditioning refrigerant circuit    Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE.Connect the negative battery terminal (-).Remove the vehicle from the lift.