125001630 - 5530A10 ALTERNATOR - R+R

Removing ( Refitting ) Position the vehicle on a lift.Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-)

	Description	Connector
-	Battery	See A1B BATTERY ( BATTERY NEGATIVE )

Proceed with the removal    Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R.Proceed with the removal    Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with the removal    Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R.Proceed with the removal    Op. 5520B10 STARTER MOTOR - R+R.Proceed with the removal    Op. 1048A59 PIPE from flow meter to throttle casing hose - R.R..Proceed with the removal    Op. 5530B10 BATTERY - R+R.Proceed with the removal    Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R..1. Remove retainer (1a), press clips (1b) and disconnect the gear engagement cable (1c).2. Press the clips (2a) and disconnect the gear selector cable (2b).3. Unscrew bolts (3a) and move aside bracket (3b) complete with gear selection and engagement cables. 1. Disconnect the electrical connection from the fuel vapour recovery solenoid valve.

	Description	Connector
1	Fuel vapour recovery solenoid valve	See L10 FUEL VAPOUR RECOVERY SOLENOID

1. Disconnect the engine wiring electrical connections (1a) and (1b) and move aside.

	Description	Connector
1a	Front/engine coupling	See D4A FRONT/ENGINE CONNECTION ( CONNECTORS )

	Description	Connector
1b	Front/engine coupling	See D4B FRONT/ENGINE CONNECTION ( CONNECTORS )

1. Undo bolts (1a), nut (1b) and remove the auxiliary drivebelt protection (1c). Proceed with the removal    Op. 4450B04 RIGHT FRONT WHEEL R R.Proceed with the removal    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..1. Adjust the mobile tensioner (1a) with a wrench and remove the auxiliary drivebelt (1b). 1. Undo the bolt (1a) and remove the engine components single belt moving tensioner (1b). 1. Disconnect the electrical connections from the alternator.

	Description	Connector
1	Alternator	See A10 ALTERNATOR

1. Unscrew the bolts securing the rear alternator bracket.2. Undo the bolts fixing the alternator.3. Recover the alternator rear mounting bracket. 1. Remove the alternator. Refitting ( Removing ) Place the alternator and its rear mounting bracket in the housing.Screw in the allternator fixing bolts without tightening them.Tighten the bolts securing the rear alternator bracket.Tighten the alternator fixing bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	-	-	-	-

	Fastening	Component	Ø	Value(daNm)
-	-	-	-	-

Connect the electrical connections to the alternator.1. Position the engine components single belt moving tensioner (1a) in its housing and secure it tightening the bolt (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	-	-	-	-

Use a wrench to turn the mobile tensioner anticlockwise and fit the auxiliary drivebelt (1b).Proceed with the refitting    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R..Proceed with the refitting    Op. 4450B04 RIGHT FRONT WHEEL R R.Refit the auxiliary drivebelt protection in its seat and secure with the nut and bolts.Refit the electrical wiring and connect the engine wiring electrical connections.Connect the electrical connection to the fuel vapour recovery solenoid valve.Refit the bracket with gear selection and engagement cables and secure with bolts.Connect the gear selector cable.Connect the gear engagement cable and secure with the retainer.Proceed with the refitting    Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R..Proceed with the refitting    Op. 5530B10 BATTERY - R+R.Proceed with the refitting    Op. 1048A59 PIPE from flow meter to throttle casing hose - R.R..Proceed with the refitting    Op. 5520B10 STARTER MOTOR - R+R.Proceed with the refitting    Op. 1076B18 RIGID SECTION OF EXHAUST PIPE BETWEEN CATALYTIC CONVERTER AND SILENCER - R + R.Proceed with the refitting    Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with the refitting    Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R.Connect the negative battery terminal (-).Remove the vehicle from the lift.