125001142 - 1080E60 PIPE FROM FUEL VAPOUR SEPARATOR TO ACTIVATED CARBON FILTER - R R

Removing ( Refitting ) Position the vehicle on a lift.Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal.

	Description	Connector
-	Battery	See A1B BATTERY ( BATTERY NEGATIVE )

Drain the air conditioning refrigerant circuit    Op. 5040A10 EXPANSION/CONNECTION PIPE - R R.Proceed with the removal    Op. 4450B04 RIGHT FRONT WHEEL R R.Proceed with the removal    Op. 4450B08 RIGHT REAR WHEEL R R.1. Disconnect the rapid connector for the pipe from the fuel vapour separator to the active charcoal filter, active charcoal filter side. 1. Undo the bolts (1a) and remove the reinforcements (1b).2. Undo the bolts and remove the power assisted steering box as far foward as necessary. Proceed with the removal    Op. 1008C10 POWER UNIT UPPER REACTION LINK R R.Proceed with the removal    Op. 1008C16 BODY LINK BRACKET - R R.Release the pipe from the fuel vapour separator to the active charcoal filter from the fastenings on the engine compartment bulkhead.1. Undo the bolts (1a) and remove the protection (1b) for the fuel supply pipe and the pipe from the fuel vapour separator to the active charcoal filter. Proceed with the removal    Op. 1040A70 SUBMERGED PUMP ASSEMBLY COMPLETE WITH LEVEL GUAGE CONTROL - R + R.Proceed with the removal    Op. 1076B22 REAR EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS.Proceed with the removal    Op. 1076B26 INTERMEDIATE EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS.Proceed with the removal    Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL.Temporarily tighten the bolts fixing the rear suspension crossmember.Remove the hydraulic jack from beneath the crossmember.1. Undo the nut (1a) and disconnect the flange (1b) for the pipe from the air conditioning compressor to the evaporator, intermediate connector side.

Seal the connectors that have been disconnected using suitable plugs to prevent dampness and impurities from entering the system.

2. Release the air conditioning system pipes from the fastenings on the side panel. 1. Undo the bolt (1a) and disconnect the supply and return pipes from the evaporator (1b), evaporator side. 1. Release the pipe from the fuel vapour separator to the active charcoal filter from the fastenings on the underbody and remove it. Refitting ( Removing ) Place the pipe from the fuel vapour separator to the active charcoal filter in position and secure it to the underbody using the fastenings.1. Connect the fuel supply and return pipes from the evaporator (1a), evaporator side and fasten them tightening the bolt (1b) to the recommended torque.

Replace the O rings for the connectors. Only use green coloured seals that are resistant to R134a refrigerant fluid.Lubricate the connector threads using anti-freeze.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	COOLANT SYSTEM FITTINGS	M6	0.7 ÷ 1.1

1. Secure the air conditioning system pipes to the side panels using the fastenings.2. Connect the flange for the pipe from the air conditioning compressor to the evaporator (2a), intermediate connector side and tighten the nut (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	Bolt	COOLANT SYSTEM FITTINGS	M6	0.7 ÷ 1.1

Position a hydraulic jack under the rear suspension crossmember.Loosen the bolts fixing the rear suspension crossmember.Proceed with the refitting    Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL.Proceed with the refitting    Op. 1076B26 INTERMEDIATE EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS.Proceed with the refitting    Op. 1076B22 REAR EXHAUST SILENCER - R+R EMISSION CONTROL VERSIONS.Adjust handbrake lever travel    Op. 3380A04 HANDBRAKE - CHECK TRAVEL.Proceed with the refitting    Op. 1040A70 SUBMERGED PUMP ASSEMBLY COMPLETE WITH LEVEL GUAGE CONTROL - R + R.Place the protection for the fuel supply pipe and the pipe from the fuel vapour separator to the active charcoal filter in position and fasten them using the bolts.Fasten the pipe from the fuel vapour separator to the active charcoal filter to the fastenings on the engine compartment bulkhead.Proceed with the refitting    Op. 1008C16 BODY LINK BRACKET - R R.Proceed with the refitting    Op. 1008C10 POWER UNIT UPPER REACTION LINK R R.1. Position the power assisted steering box in its housing and secure it tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	POWER STEERING BOX	M14	(Front suspension crossmember side) 11.7 - 14.3

2. Place the reinforcements (2a) in their housings and secure them using the bolts (2b). Connect the rapid connector for the pipe from the fuel vapour separator to the active charcoal filter, active charcoal filter side.Proceed with the refitting    Op. 4450B08 RIGHT REAR WHEEL R R.Proceed with the refitting    Op. 4450B04 RIGHT FRONT WHEEL R R.Refill the air conditioning refrigerant circuit    Op. 5040A10 EXPANSION/CONNECTION PIPE - R R.Connect the negative battery terminal (-).Remove the vehicle from the lift.