125000983 - 1036E10 LEFT CYLINDER HEAD TIMING SYSTEM SHAFTS - R.R. ON CAR

Removing ( Refitting ) Position the vehicle on the rampProceed with removal    Op. 4450B04 RIGHT FRONT WHEEL R RProceed with removalProceed with removal    Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R RProceed with removalProceed with removal    Op. 1092G10 SINGLE ENGINE BELT R RProceed with removalProceed with removal    Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R.Proceed with removalProceed with removal    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + RProceed with removalProceed with removal    Op. 1016A42 LEFT HAND CYLINDER HEAD IGNITION COIL COVER - R+RProceed with removalProceed with removal    Op. 5510C16 LEFT HAND CYLINDER HEAD IGNITION COIL - R+R1. Undo the bolts (1a) and remove the timing belt fixed tensioners (1b).2. Undo the bolts (2a) and remove the rear left timing belt guard (2b).    Op. 1016A30 LEFT CAM COVER - R + R AND REPLACE GASKET3. Undo the bolts (3a) and remove the camshaft caps (3b) from the left cylinder head.4. Remove the left cylinder head camshafts complete with oil seals.    Op. 1072B50 SLEEVES CONNECTING AIR CAPACITY BOX TO INLET MANIFOLD IS - R+R    Op. 5510C18 RIGHT HAND CYLINDER HEAD IGNITION COIL - R+R    Op. 1016A34 RIGHT-HAND CAM COVER - R + R AND REPLACE GASKET    Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT    Op. 1032B54 LEFT CYLINDER HEAD DRIVEN TOOTHED PULLEYS - R.R.
Refitting ( Removing ) Place the camshafts back in their housings for the left cylinder head.Place the camshaft caps back in their housings in the left cylinder head following the sequence shown in the diagram.
Tighten the camshaft cap bolts for the left cylinder head to the specified torque.

FasteningComponentØValue(daNm)
-BoltCAMSHAFT CAPS/M8(Cylinder head side) 1.8 ÷ 2.0
1. Fit the camshaft front oil seals (1a) using the tool (1b).

NameCountry
1bFitting tool1.860.948.000
1. Place the timing belt left rer guard (1a) back in its housing and secure it using the bolts (1b).2. Place the timing belt fixed tensioners (2a) back in their housings and secure them tightening the bolts (2b) to the recommended torque.

FasteningComponentØValue(daNm)
2bBoltFIXED TENSIONERM10(Cylinder head side) 4.5 ÷ 5.5
Proceed with refitting    Op. 1032B54 LEFT CYLINDER HEAD DRIVEN TOOTHED PULLEYS - R.R..Proceed with refitting    Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT.Proceed with refitting    Op. 1016A34 RIGHT-HAND CAM COVER - R + R AND REPLACE GASKET.Proceed with refitting    Op. 5510C18 RIGHT HAND CYLINDER HEAD IGNITION COIL - R+R.Proceed with refitting    Op. 1072B50 SLEEVES CONNECTING AIR CAPACITY BOX TO INLET MANIFOLD IS - R+R.Proceed with refitting    Op. 1016A30 LEFT CAM COVER - R + R AND REPLACE GASKET.Proceed with refitting    Op. 5510C16 LEFT HAND CYLINDER HEAD IGNITION COIL - R+R.Proceed with refitting    Op. 1016A42 LEFT HAND CYLINDER HEAD IGNITION COIL COVER - R+R.Proceed with refitting    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R.Proceed with refitting    Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R..Proceed with refitting    Op. 1092G10 SINGLE ENGINE BELT R R.Proceed with refitting    Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.Proceed with refitting    Op. 4450B04 RIGHT FRONT WHEEL R R.Remove the car from the ramps.