125001161 - 1084B34 CARTRIDGE ENGINE OIL FILTER SUPPORT - R + R

Removing ( Refitting ) Position the vehicle on a lift.Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-)

	Description	Connector
-	Battery	See A1B BATTERY ( BATTERY NEGATIVE )

Drain the air conditioning refrigerant circuit    Op. 5040A10 EXPANSION/CONNECTION PIPE - R R.Proceed with the removal    Op. 4450B04 RIGHT FRONT WHEEL R R.Proceed with the removal    Op. 7055B54 UNDER-ENGINE GUARD - R R.Proceed with the removal    Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.Proceed with the removal    Op. 7055B42 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.Proceed with the removal    Op. 7210E10 R.R. FRONT BUMPER.Proceed with the removal    Op. 5540B76 FRONT LIGHT CLUSTER WITH FOGLAMP ONE LH OR RH R R WITH INTERFERING PARTS REMOVED(Right and left sides).Proceed with the removal    Op. 7025A34 BONNET LID LOCK (ONE) - R+R OR REPAIR.Proceed with removal - 7210A15 R&R FRONT WING/HEADLAMP HOUSING CROSSMEMBER .Proceed with the removal    Op. 1076B82 LEFT EXHASUST PIPE BETWEEN CATALYTIC PRECONVERTER AND CONVERTER R R.Proceed with the removal    Op. 1076B84 RIGHT EXHAUST PIPE BETWEEN CARALYTIC PRECONVERTER AND CONVERTER R R.Proceed with the removal    Op. 1080B39 RIGHT CATALYTIC PRECONVERTER R R OR REPLACE CYLINDER HEAD GASKET.Proceed with the removal    Op. 4410A80 DAMPER LOWER FORK - R R.Proceed with the removal    Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R R.1. Disconnect the electrical connections from the alternator.

	Description	Connector
1	Alternator	See A10 ALTERNATOR

2. Loosen the band (2a) and move the electrical wiring (2b).3. Undo the connector (3a) and disconnect the engine oil supply pipe to the cooling radiator (3b), engine oil cartridge filter mounting side.

Collect the engine oil that comes out in a suitable container.

4. Undo the upper bolt (4a) and the nut (4b) fixing the catridge engine oil filter mounting.5. Disconnect the electrical connection from the engine oil pressure warning light switch.

	Description	Connector
5	Engine oil pressure sensor (switch)	See K30 ENGINE OIL PRESSURE SENSOR SWITCH ( CONNECTORS )

6. Undo and remove the cartridge engine oil filter using a suitable tool.

Collect the engine oil that comes out in a suitable container.

1. Loosen the tension for the auxiliary drive belt using the tensioner.2. Lock the tensioner (2a) in place so that the belt is slack by inserting a pin (2b).3. Release and remove the auxiliary drivebelt. 1. Disconnect the electrical connection from the engine oil temperature sender unit.2. Undo the bolt (2a) and remove the engine components single belt fixed tensioner (2b).3. Undo the lower bolt (3a), loosen the upper bolt (3b) and rotate the alternator (3c) upwards locking it in position using the upper bolt. 1. Undo the nut (1a) and remove the bracket (1b) supporting the engine oil/power assisted steering pipes. 1. Undo the bolt (1a) and remove the lower bracket (1b) supporting the engine oil/power assisted steering pipes.2. Undo the bolts (2a) and remove the upper bracket (2b) supporting the engine oil/power assisted steering pipes. 1. Undo the connector (1a) and disconnect the engine oil return pipe to the cooling radiator (1b), engine oil cartridge filter mounting side. 1. Undo the bolts fixing the alternator mounting to the crankcase. 1. Unscrew the bolt securing the right rear timing belt cover to the alternator spacer.2. Undo the lower bolt fixing the alternator mount spacer bracket to the crankcase.3. Undo the upper bolt securing the alternator mount spacer bracket to the right cylinder head.4. Move the alternator assembly (4a), alternator mounting (4b) and alternator mounting spacer bracket (4c) away from the engine block. 1. Undo the nuts (1a) and bolts (1b) and remove the cartridge engine oil filter support (1c).2. Remove the gasket. Refitting ( Removing ) 1. Place the cartridge engine oil filter mounting (1a) in position complete with gasket (1b) and secure it tightening the bolts (1c) and the nuts (1d) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1c	Bolt	DRIVE SHAFT OIL FILTER/BEARING MOUNT	M8	(Engine crankcase side) 2.3 - 2.8

	Fastening	Component	Ø	Value(daNm)
1d	Bolt	DRIVE SHAFT OIL FILTER/BEARING MOUNT	M8	(Engine crankcase side) 2.3 - 2.8

Place the alternator assembly, alternator mounting and alternator mounting spacer bracket in its housing.Tighten the bolts securing the alternator spacer bracket.Tighten the bolt securing the right rear timing belt cover to the alternator spacer.1. Tighten the bolts fixing the alternator mounting to the engine block to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	ALTERNATOR SUPPORT	M8	(Engine crankcase side) 1.9 - 2.3

	Fastening	Component	Ø	Value(daNm)
1	Bolt	ALTERNATOR SUPPORT	M10	(Engine crankcase side) 4.3 - 5.3

1. Connect the engine oil return pipe to the cooling radiator (1a), engine oil cartridge filter mounting side and tighten the connector (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	-	-	-	-

Place the engine oil/power assisted steering pipes upper mounting bracket in its housing and secure it using the bolts.Place the engine oil/power assisted steering pipes lower mounting bracket in its housing and secure it using the bolt.Place the engine oil/power assisted steering pipes mounting bracket in its housing and secure it using the nut.1. Tighten the alternator fixing bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	ALTERNATOR ASSEMBLY	M8	(Mount side) 2.3 - 2.8

2. Position the auxiliary drivebelt fixed tensioner (2a) in its housing and secure it tightening the bolt (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	Bolt	SINGLE BELT FIXED TENSIONER VARIOUS	M8	2.3 ÷ 3.3

3. Connect the electrical connection to the engine oil temperature sender unit. Fit the engine components single drive belt.Adjust the mobile tensioner with a wrench until the pin can be withdrawn.1. Lubricate the seal with engine oil and fit the engine oil filter tightening it fully by hand.2. Connect the electrical connection to the engine oil pressure warning light switch.3. Connect the engine oil supply pipe to the cooling radiator (3a), engine oil cartridge filter mounting side and tighten the connector (3b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
3b	-	-	-	-

4. Place the electrical wiring (4a) in position and fasten it with the band (4b).5. Connect the electrical connections to the alternator. Proceed with the refitting    Op. 2710A31 INTERMEDIATE DRIVE SHAFT - R R.Proceed with the refitting    Op. 4410A80 DAMPER LOWER FORK - R R.Proceed with the refitting    Op. 1080B39 RIGHT CATALYTIC PRECONVERTER R R OR REPLACE CYLINDER HEAD GASKET.Proceed with the refitting    Op. 1076B84 RIGHT EXHAUST PIPE BETWEEN CARALYTIC PRECONVERTER AND CONVERTER R R.Proceed with the refitting    Op. 1076B82 LEFT EXHASUST PIPE BETWEEN CATALYTIC PRECONVERTER AND CONVERTER R R.Proceed with refitting - 7210A15 R&R FRONT WING/HEADLAMP HOUSING CROSSMEMBER .Proceed with the refitting    Op. 7025A34 BONNET LID LOCK (ONE) - R+R OR REPAIR.Proceed with the refitting    Op. 5540B76 FRONT LIGHT CLUSTER WITH FOGLAMP ONE LH OR RH R R WITH INTERFERING PARTS REMOVED(Right and left sides).Proceed with the refitting    Op. 7210E10 R.R. FRONT BUMPER.Proceed with the refitting    Op. 7055B42 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.Proceed with the refitting    Op. 7055B64 LH OR RH REFLECTOR(ONE) ON REAR BUMPERS - R R.Proceed with the refitting    Op. 4450B04 RIGHT FRONT WHEEL R R.Refill the engine oil lubrication system    Op. 0010T11 ENGINE OIL CHECK LEVEL AND TOP UP.Proceed with the refitting    Op. 7055B54 UNDER-ENGINE GUARD - R R.Refill the air conditioning refrigerant circuit    Op. 5040A10 EXPANSION/CONNECTION PIPE - R R.Connect the negative battery terminal (-).Remove the vehicle from the lift.