4450C10 FRONT PILLAR (ONE), L/H OR R/H COMPLETE WITH WHEEL HUB - R+R WITH WHEEL REMOVED - CHECK WHEEL GEOMETRY SEPARATELY - Alfa - GT - eLearn

125001482 - 4450C10 FRONT PILLAR (ONE), L/H OR R/H COMPLETE WITH WHEEL HUB - R+R WITH WHEEL REMOVED - CHECK WHEEL GEOMETRY SEPARATELY

) Position the vehicle on the rampEnsure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-).

	Name	Connector
-	Battery	See A1B BATTERY ( BATTERY NEGATIVE )

Remove the wheel arch liner from the wheel housing involvedProceed with removal Op. 7055B54 UNDER-ENGINE GUARD - R R. 1. Release the front brake caliper flexible pipe from the mounting bracket.2. Undo the bolts (2a) and move the bracket (2b) complete with brake caliper (2c) without disconnecting the pipe.

1. Undo bolt (1a) and remove the front wheel rpm sensor (1b) from its seat and move aside after releasing the electrical wiring from its fastenings.

1. Unscrew the pin (1a) and remove the front brake disc (1b).2. Unscrew nut (2a) and disconnect steering link (2b) from the front wheel strut using tool (2c).

	Name	Country
2c	Extractor	1.821.169.000

1. Undo the nut (1a) and disconnect the front upper wishbone (1b) from the knuckle using the tool (1c).

	Name	Country
1c	Extractor	1.821.169.000

1. Undo the nut (1a) and disconnect the front suspension lower wishbone from the steering knuckle using the tool (1b).

	Name	Country
1b	Extractor	1.821.169.000

2. Remove front knuckle (2a) with wheel hub (2b).

Refitting ( Removing

) 1. Refit front knuckle (1a) complete with wheel hub (1b).2. Connect the front suspension lower wishbone to the front steering knuckle and fix it by tightening the nut to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2	Nut	FRONT SUSPENSION LOWER LEVER	M14	(Steering knuckle side) 8.1 ÷ 9.9

1. Connect the front upper wishbone (1a) to the steering knuckle and fix it tightening the nut (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Nut	FRONT SUSPENSION TOP LEVER	M10	(Steering knuckle side) 4.3 ÷ 4.7

1. Connect the steering link (1a) to the front steering knuckle and fix it tightening the nut (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Nut	ADJUSTABLE STEERING LINKS	M10	(Front steering knuckle side) 3.2 ÷ 3.9

2. Place the front brake disc (2a) back in its housing and fix it tightening the pin (2b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2b	Pin	FRONT BRAKE DISC.	M8	(Wheel hub side) 1.0 ÷ 1.4

Place the front wheel rpm sensor back in its housing and fix it tightening the bolt to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	ABS SYSTEM FRONT WHEEL RPM SENSOR	M6	06 10

Secure the front wheel rpm sensor electrical wiring. 1. Tighten the nut (1a) fixing the wheel hub to the drive shaft to the recommended torque, using the angle tightening tool (1b).

	Fastening	Component	Ø	Value(daNm)
1a	Nut	FRONT HUB WITH BEARINGS	M24	(Driveshaft side 67 74 62 2

	Name	Country
1b	Protractor	1.860.942.000

Top up the brake-clutch fluid level Op. 0010T64 BRAKE AND OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY.Bleed the air from the hydraulic braking system Op. 0010T65 HYDRAULIC BRAKE SYSTEM BLEED AIR. Place the wheel arch liner in the wheel housing involved.Connect the negative (-) battery terminalRemove the car from the ramps.It is advisable to check the wheel alignment Op. 4450A10 FRONT WHEEL GEOMETRY - CHECK USING OPTICAL EQUIPMENT - INCLUDES FRONT WHEEL TOW-IN ADJUSTMENT IF NECESSARY. Remove the protective cap on the brake caliper bleed valve.Connect the collection system (pipe and reservoir) to the bleed valve on the brake caliper.Operate the brake pedal until the brake-clutch reservoir and pipes are empty.1. Undo the connectors (1a) and remove the rigid pipe to the brake caliper (1b).2. Disconnect the electrical connections for the brake pad wear cable.

	Name	Connector
2	Left brake pad wear sensor switch	See K20 LEFT BRAKE PAD WEAR SENSOR SWITCH ( FRONT )

3. Undo the bolts (3a) and remove the front brake caliper (3b) complete with brake pads.

1. Refit the rear brake caliper assembly (1a) complete with pads and tighten the bolts (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	FRONT BRAKE CALIPER ASSEMBLY	M12

2. Connect the electrical connection for the brake pad wear cable.3. Refit the rigid pipe to the brake caliper (3a) in its seating and tighten the connectors (3b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
3b	Connector	FITTING FOR PIPE TO CALIPER	M10	(Brake caliper side) 1.4 ÷1.8

	Fastening	Component	Ø	Value(daNm)
3b	Connector	FITTING FOR PIPE TO CALIPER	M10	(Flexible pipe side) 1.4 ÷ 1.8

1. Tighten the nut (1a) fixing the wheel hub to the drive shaft to the recommended torque, using the angle tightening tool (1b).

	Fastening	Component	Ø	Value(daNm)
1a	Nut	FRONT HUB WITH BEARINGS	M24	(Driveshaft side 67 74 41 2

	Name	Country
1b	Protractor	1.860.942.000