125001142 - 1080E60 PIPE FROM FUEL VAPOUR SEPARATOR TO ACTIVATED CARBON FILTER - R R

Removing ( Refitting )

• Position the vehicle on a lift.
• Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).

	Description	Connector
-	Battery	See A001 Battery

•     Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE
•     Op. 4450B04 RIGHT FRONT WHEEL R R
•     Op. 4450B08 RIGHT REAR WHEEL R R
•     Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R

• Disconnect the rapid connector for the pipe from the fuel vapour separator to the active charcoal filter, active charcoal filter side.

• Undo the bolts and remove the power assisted steering box as far foward as necessary.

• Release the pipe from the fuel vapour separator to the active charcoal filter from the fastenings on the engine compartment bulkhead.

• Undo the bolts (1a) and remove the protection (1b) for the fuel supply pipe and the pipe from the fuel vapour separator to the active charcoal filter.

• Disconnect the rapid connector for the pipe from the fuel vapour separator to the active charcoal filter, separator side.

1. Undo the nut (1a) and disconnect the flange (1b) for the pipe from the condenser to the intermediate connector, intermediate connector side.

Seal the connectors that have been disconnected using suitable plugs to prevent dampness and impurities from entering the system.

2. Release the air conditioning system pipes from the fastenings on the side panel.

• Undo the bolt (1a) and disconnect the supply and return pipes from the evaporator (1b), evaporator side.

• Release the pipe from the fuel vapour separator to the active charcoal filter from the fastenings on the underbody and remove it.

Refitting ( Removing )

• Place the pipe from the fuel vapour separator to the active charcoal filter in position and secure it to the underbody using the fastenings.

1. Connect the fuel supply and return pipes from the evaporator (1a), evaporator side and fasten them tightening the bolt (1b) to the recommended torque.

Replace the O rings for the connectors. Only use green coloured seals that are resistant to R134a refrigerant fluid. Lubricate the connector threads using anti-freeze.

	Fastening	Component	Ø	Value (daNm)
1b	Bolt	EVAPORATOR INLET/OUTLET PIPES	M6	(Evaporator side) 0.7 - 1.1

• Secure the air conditioning system pipes to the side panels using the fastenings.
• Connect the flange for the pipe from the air conditioning condenser to the intermediate connector (2a), intermediate connector side and tighten the nut (2b) to the recommended torque.

	Fastening	Component	Ø	Value (daNm)
2b	Nut	COOLANT CIRCUIT CONNECTORS	M6	0.7 ÷ 1.1

• Connect the rapid connector for the pipe from the fuel vapour separator to the active charcoal filter, separator side.
• Place the protection for the fuel supply pipe and the pipe from the fuel vapour separator to the active charcoal filter in position and fasten them using the bolts.
• Fasten the pipe from the fuel vapour separator to the active charcoal filter using the fastenings on the engine compartment bulkhead.
• Position the power assisted steering box in its housing and secure it tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value (daNm)
-	Bolt	POWER STEERING BOX	M14	(Front suspension crossmember side) 11.7 - 14.3

• Connect the rapid connector for the pipe from the fuel vapour separator to the active charcoal filter, active charcoal filter side.
•     Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R
•     Op. 4450B08 RIGHT REAR WHEEL R R
•     Op. 4450B04 RIGHT FRONT WHEEL R R
•     Op. 0010T84 COOLANT FOR AIR CONDITIONING SYSTEM DEHYDRATE AND RECHARGE
• Connect the negative battery terminal (-).
• Remove the vehicle from the lift.