125001377 - 3340B67 RH BRAKE CONNECTION PIPE - R R

Removing ( Refitting ) Position the vehicle on a lift.Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-)

	Description	Connector
-	Battery	See A1B BATTERY ( BATTERY NEGATIVE )

Proceed with the removal    Op. 4450B08 RIGHT REAR WHEEL R R.Proceed with the removal    Op. 7055B45 RIGHT HAND REAR SUPPLEMENTARY WHEEL ARCH - R+R.Proceed with the removal    Op. 1040A70 SUBMERGED PUMP ASSEMBLY COMPLETE WITH LEVEL GUAGE CONTROL - R + R.Proceed with the removal    Op. 1040A30 OIL SEAL COVER, FLY WHEEL SIDE - R + R AND REPLACE SEALS.Release the handbrake boot and remove it.Proceed with the removal    Op. 1076B20 REAR EXHAUST SILENCER - R + R.Proceed with the removal    Op. 1076B30 FRONT EXHAUST SILENCER - R + R.Proceed with the removal    Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL.1. Release the rigid pipe from the fitting to the right rear brake from the underbody fastenings.2. Undo the connector (2a) and disconnect the rigid pipe from the fitting to the right front brake (2b), fitting side. 1. Undo the connector (1a) and disconnect the rigid pipe from the fitting to the right rear brake (1b), right rear brake side.Remove the rigid pipe from the fitting to the right rear brake. Refitting ( Removing ) Replace the rigid pipe from the fitting to the right rear brake.1. Connect the rigid pipe from the fitting to the right rear brake (1a), right rear brake side and tighten the connector (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	RIGID PIPE FROM FITTING/REAR BRAKES (ABS)	M10	(rear brake caliper hose side) 1.3 ÷ 1.5

1. Connect the rigid pipe from the fitting to the right rear brake (1a), fitting side and tighten the connector (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	RIGID PIPE FROM FITTING/REAR BRAKES (ABS)	M10	(Fitting side) 1.3 - 1.5

2. Fasten the rigid pipe from the fitting to the right rear brake to the underbody fastenings. Proceed with the refitting    Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL.Proceed with the refitting    Op. 1076B30 FRONT EXHAUST SILENCER - R + R.Proceed with the refitting    Op. 1076B20 REAR EXHAUST SILENCER - R + R.Proceed with the refitting    Op. 1040A30 OIL SEAL COVER, FLY WHEEL SIDE - R + R AND REPLACE SEALS.Proceed with the refitting    Op. 1040A70 SUBMERGED PUMP ASSEMBLY COMPLETE WITH LEVEL GUAGE CONTROL - R + R.Proceed with the refitting    Op. 0010T64 BRAKE AND OR CLUTCH FLUID CHECK LEVEL AND TOP UP AS NECESSARY.Proceed with the refitting    Op. 0010T65 HYDRAULIC BRAKE SYSTEM BLEED AIR.Adjust handbrake lever travel    Op. 3380A04 HANDBRAKE - CHECK TRAVEL.Place the handbrake lever boot in position.Proceed with the refitting    Op. 7055B45 RIGHT HAND REAR SUPPLEMENTARY WHEEL ARCH - R+R.Proceed with the refitting    Op. 4450B08 RIGHT REAR WHEEL R R.Connect the negative battery terminal (-).Remove the vehicle from the lift. Removing ( Refitting ) Position the vehicle on a lift.Make sure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-)

	Description	Connector
-	Battery	A1B

Proceed with the removal    Op. 4450B08 RIGHT REAR WHEEL R RProceed with the removal    Op. 7055B45 RIGHT HAND REAR SUPPLEMENTARY WHEEL ARCH - R+RProceed with the removal    Op. 1040A70 SUBMERGED PUMP ASSEMBLY COMPLETE WITH LEVEL GUAGE CONTROL - R + R.Proceed with the removal    Op. 1040A30 OIL SEAL COVER, FLY WHEEL SIDE - R + R AND REPLACE SEALS.Release the handbrake boot and remove it.Proceed with the removal    Op. 1076B20 REAR EXHAUST SILENCER - R + R.Proceed with the removal    Op. 1076B24 INTERMEDIATE EXHAUST SILENCER - R + R.Proceed with the removal    Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL.1. Release the rigid pipe from the fitting to the right rear brake from the underbody fastenings.2. Undo the connector (2a) and disconnect the rigid pipe from the fitting to the right front brake (2b), fitting side. 1. Undo the connector (1a) and disconnect the rigid pipe from the fitting to the right rear brake (1b), right rear brake side.Remove the rigid pipe from the fitting to the right rear brake. Refitting ( Removing ) Replace the rigid pipe from the fitting to the right rear brake.1. Connect the rigid pipe from the fitting to the right rear brake (1a), right rear brake side and tighten the connector (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	RIGID PIPE FROM FITTING/REAR BRAKES (ABS)	M10	(rear brake caliper hose side) 1.3 ÷ 1.5

1. Connect the rigid pipe from the fitting to the right rear brake (1a), fitting side and tighten the connector (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Connector	RIGID PIPE FROM FITTING/REAR BRAKES (ABS)	M10	(Fitting side) 1.3 - 1.5

2. Fasten the rigid pipe from the fitting to the right rear brake to the underbody fastenings. Proceed with the refitting    Op. 1040A10 FUEL TANK - R + R AND DECANT FUEL.Proceed with the refitting    Op. 1076B24 INTERMEDIATE EXHAUST SILENCER - R + R.Proceed with the refitting    Op. 1076B20 REAR EXHAUST SILENCER - R + R.Proceed with the refitting    Op. 1040A30 OIL SEAL COVER, FLY WHEEL SIDE - R + R AND REPLACE SEALS.Proceed with the refitting    Op. 1040A70 SUBMERGED PUMP ASSEMBLY COMPLETE WITH LEVEL GUAGE CONTROL - R + R.Bleed the air from the hydraulic braking system    Op. 0010T65 HYDRAULIC BRAKE SYSTEM BLEED AIR.Adjust handbrake lever travel    Op. 3380A04 HANDBRAKE - CHECK TRAVEL.Place the handbrake lever boot in position.Proceed with the refitting    Op. 7055B45 RIGHT HAND REAR SUPPLEMENTARY WHEEL ARCH - R+RProceed with the refitting    Op. 4450B08 RIGHT REAR WHEEL R RConnect the negative battery terminal (-).Remove the vehicle from the lift.