125001436 - 4410B40 LOWER WISHBONE (WITH BALLJOINT) OF LEFT OR RIGHT FRONT SUSPENSION (ONE) - R+R -CHECK WHEEL GEOMETRY SEPARATELY

Removing ( Refitting ) Position the vehicle on the rampEnsure that the ignition key is in the OFF position, then disconnect the negative battery terminal (-).

	Name	Connector
-	Battery	See A1B BATTERY ( BATTERY NEGATIVE )

PROCEED AS FOLLOWS FOR THE LEFT LOWER TRACK CONTROL ARMProceed with removal    Op. 4450B02 LEFT FRONT WHEEL R RProceed with removalPROCEED AS FOLLOWS FOR THE RIGHT LOWER TRACK CONTROL ARM    Op. 7055B65 ENGINGE BAY DUSTGUARD PROTECTION IN LEFT FRONT WHEEL ARCH R RProceed with removalProceed with removalPROCEED AS FOLLOWS FOR BOTH LOWER TRACK CONTROL ARMS    Op. 4450B04 RIGHT FRONT WHEEL R RProceed with removalProceed with removal    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.1. Undo the nuts (1a) and disconnect the front anti-roll bar joint (1b) from the fork.2. Remove the brake pad wear sensor electric wiring bracket.3. Undo bolt (3a) and remove the lower fork connecting the front suspension damper to lower wishbone (3b).    Op. 7055B54 UNDER-ENGINE GUARD - R R4. Remove the wheel rpm sensor electric wiring and brake caliper hose bracket.    Op. 4450C10 FRONT PILLAR (ONE), L/H OR R/H COMPLETE WITH WHEEL HUB - R+R WITH WHEEL REMOVED - CHECK WHEEL GEOMETRY SEPARATELY 1. Undo the bolts securing the antiroll bar to the front suspension (wishbone removal side).Loosen the bolts fixing the anti-roll bar to the front suspension crossmember (opposite side to wishbone removal side).2. Remove bolts (2a) and remove front suspension lower wishbone (2b). Refitting ( Removing ) 1. Refit the front suspension lower wishbone (1a) in its seating and secure by tightening bolts (1b) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	FRONT SUSPENSION LOWER LEVER	M10	(Front suspension crossmember side) 7.1 ÷ 7.9

2. Tighten the bolts securing the front anti-roll bar to the front suspension crossmember to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2	Bolt	FRONT ANTI-ROLL BAR	M8	(Front suspension crossmember side) 3.6 ÷ 4.4

1. Refit the lower fork connecting the front suspension damper to the lower wishbone (1a) complete with bracket (1b) and secure by tightening bolt (1c) to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1c	Bolt	FRONT DAMPER FORK ON WISHBONE	M12	(Shock absorber side) 7.2 ÷ 8.8

2. Connect the front anti-roll bar joint (2a) to the fork and secure together with bracket (2b) by tightening the nut (2c) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2c	Nut	FRONT ANTI-ROLL BAR JOINTS	M10	(Front shock absorber fork side) 4.1 ÷ 5.0

Proceed with refitting    Op. 4450C10 FRONT PILLAR (ONE), L/H OR R/H COMPLETE WITH WHEEL HUB - R+R WITH WHEEL REMOVED - CHECK WHEEL GEOMETRY SEPARATELY.Proceed with refitting    Op. 7055B54 UNDER-ENGINE GUARD - R R.PROCEED AS FOLLOWS FOR THE RIGHT LOWER TRACK CONTROL ARMProceed with removal    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.Proceed with removalPROCEED AS FOLLOWS FOR THE LEFT LOWER TRACK CONTROL ARM    Op. 4450B04 RIGHT FRONT WHEEL R RProceed with removalProceed with removalPROCEED AS FOLLOWS FOR THE BOTH LOWER TRACK CONTROL ARMS    Op. 7055B65 ENGINGE BAY DUSTGUARD PROTECTION IN LEFT FRONT WHEEL ARCH R RConnect the negative (-) battery terminalRemove the car from the ramps.    Op. 4450B02 LEFT FRONT WHEEL R RIt is advisable to check the wheel alignment.    Op. 4450A10 FRONT WHEEL GEOMETRY - CHECK USING OPTICAL EQUIPMENT - INCLUDES FRONT WHEEL TOW-IN ADJUSTMENT IF NECESSARY