125001630 - 5530A10 ALTERNATOR - R+R

Removing ( Refitting )

• Position the vehicle on a lift.
• Make sure that the ignition key is in the OFF position, then disconnect the battery terminal (-).
•     Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R
•     Op. 1072C44 EXHAUST MANIFOLD HEAT SHIELD ON BULKHEAD - R+R
•     Op. 1080B40 CATALYTIC PRE-CONVERTER - R R
•     Op. 5520B10 STARTER MOTOR - R+R
•     Op. 5530B10 BATTERY - R+R
•     Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R.

• Disconnect the gear selector and engagement cables.

To disconnect the gear selection cable, press the release tabs shown in the figure and withdraw the cable.

2. Remove the retaining plates (2a) and release the gear selector and engagement cables rom the mounting bracket (2b).

• Disconnect the electrical connection from the fuel vapour recovery solenoid valve.

	Description	Connector
1	FUEL VAPOUR RECOVERY SOLENOID	See L10 FUEL VAPOUR RECOVERY SOLENOID

• Disconnect the engine wiring electrical connections (1a) and (1b) and move aside.

	Description	Connector
1a	Front/engine coupling	See D4 FRONT/ENGINE JUNCTION

	Description	Connector
1b	Front/engine coupling	See D4 FRONT/ENGINE JUNCTION

• Undo bolts (1a), nut (1b) and remove the auxiliary drivebelt protection (1c).

•     Op. 4450B04 RIGHT FRONT WHEEL R R
•     Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.

• Adjust the mobile tensioner (1a) with a wrench and remove the auxiliary drivebelt (1b).

• Undo the bolt (1a) and remove the engine components single belt moving tensioner (1b).

• Disconnect the electrical connections from the alternator.

	Description	Connector
1	ALTERNATOR	See A10 ALTERNATOR

• Unscrew the bolts securing the rear alternator bracket.
• Undo the bolts fixing the alternator.
• Recover the alternator rear mounting bracket.

• Remove the alternator.

Refitting ( Removing )

• Place the alternator and its rear mounting bracket in the housing.
• Screw in the allternator fixing bolts without tightening them.
• Tighten the bolts securing the rear alternator bracket.
• Tighten the alternator fixing bolts to the recommended torque.

	Fastening	Component	Ø	Value (daNm)
-	Bolt	ALTERNATOR ASSEMBLY

• Connect the electrical connections to the alternator.

• Position the engine components single belt moving tensioner (1a) in its housing and secure it tightening the bolt (1b) to the recommended torque.

	Fastening	Component	Ø	Value (daNm)
-	Bolt	SINGLE BELT MOVING TENSIONER VARIOUS

• Use a wrench to turn the mobile tensioner anticlockwise and fit the auxiliary drivebelt (1b).
•     Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.
•     Op. 4450B04 RIGHT FRONT WHEEL R R
• Refit the auxiliary drivebelt protection in its seat and secure with the nut and bolts.
• Refit the electrical wiring and connect the engine wiring electrical connections.
• Connect the electrical connection to the fuel vapour recovery solenoid valve.
• Connect the gear selection and engagement cables and secure to the mounting bracket with the retaining plates.
•     Op. 5530B52 BATTERY DRIP TRAY/SUPPORT - R.R.
•     Op. 5530B10 BATTERY - R+R
•     Op. 5520B10 STARTER MOTOR - R+R
•     Op. 1080B40 CATALYTIC PRE-CONVERTER - R R
•     Op. 1072C44 EXHAUST MANIFOLD HEAT SHIELD ON BULKHEAD - R+R
•     Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R
• Connect the negative battery terminal (-).
• Remove the vehicle from the lift.