125002600 - 1056B51 CAM ANGLE SENSOR R + R

Removing ( Refitting ) Proceed with the removal    Op. 4450B04 RIGHT FRONT WHEEL R RProceed with the removal    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.Proceed with the removal    Op. 1092G10 SINGLE ENGINE BELT R R.Proceed with the removal    Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R..Proceed with the removal    Op. 1092G20 ENGINE COMPONENT SINGLE BELT FIXED TENSIONER - ONE - R + R.Proceed with the removal    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R.Proceed with the removal    Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R.Proceed with the removal Op. 5510C14 IGNITION COIL/S - R+R.Proceed with the removal    Op. 1016A20 SINGLE CAM COVER - R + R AND REPLACE GASKET.Proceed with the removal    Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT.Proceed with the removal    Op. 1088C14 WATER PUMP - R + R WITH DRIVE BELT REMOVED.1. Undo the bolt (1a) for the exhaust side driven toothed pulley using the tools (1b) and (1c) for counter-torque.

	Description	Code
1b	Counter-torque	1.822.156.000

	Description	Code
1c	Counter-torque	1.822.146.000

2. Remove the exhaust side toothed driven pulley. 1. Undo the bolts (1a) and move the power steering fluid reservoir (1b) without disconnecting the pipes. 1. Disconnect the electrical connection from the cam angle sensor and release the wiring from the fastenings on the modular intake manifold.

	Description	Connector
1	Timing sensor	K47

2. Release the cam angle sensor electrical wiring from the collar on the power steering reservoir bracket. 1. Undo the bolts (1a) and remove the cam angle sensor (1b) with the electrical wiring. Refitting ( Removing ) Place the cam angle sensor with its wiring back in its housing and secure it by tightening the bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CAM ANGLE SENSOR	M6	(Cylinder head side) 0.8 - 1.0

Fasten the cam angle sensor electrical wiring using the collar on the power steering reservoir bracket.Connect the cam angle sensor electrical connection and secure the wiring to the fastening on the modular intake manifold.Refit the power steering fluid reservoir and secure with the bolts.Refit the exhaust side toothed driven pulley in its seat and secure with the bolt without tightening.Proceed with the refitting    Op. 1088C14 WATER PUMP - R + R WITH DRIVE BELT REMOVED.Proceed with the refitting    Op. 1032B10 TOOTHED TIMING BELT - R + R FOR TIMING ADJUSTMENT OR REPLACEMENT.Proceed with the refitting    Op. 1016A20 SINGLE CAM COVER - R + R AND REPLACE GASKET.Proceed with the refitting Op. 5510C14 IGNITION COIL/S - R+R..Proceed with the refitting    Op. 1016A40 IGNITION COIL COVER ON CYLINDER HEAD- R+R.Proceed with the refitting    Op. 1032D12 TIMING SYSTEM PROTECTIVE COVER(S) - R + R.Proceed with the refitting    Op. 1092G20 ENGINE COMPONENT SINGLE BELT FIXED TENSIONER - ONE - R + R.Proceed with the refitting    Op. 1092A10 CRANKSHAFT SERVICES PULLEY - R.R..Proceed with the refitting    Op. 1092G10 SINGLE ENGINE BELT R R.Proceed with the refitting    Op. 7055B66 ENGINE COMPARTMENT DUST SHIELD PROTECTION IN RIGHT FRONT WHEEL ARCH - R.R.Proceed with the refitting    Op. 4450B04 RIGHT FRONT WHEEL R R