2398822 - K33 DOORS OPEN CHECK WARNING LIGHT ON

After having carried out the initial test, the lights check warning light in the Instrument Panel Node should remain on constantly.

		Results of the tests
0	PRELIMINARY CHECKS	All OK	Problems met	Operation
	Press the button which switches on the parking lights, move the stalk unit lever and check that the parking lights come on properly.Press the hazard warning lights switch and check that they are correctly activated. Then turn the ignition key to the ON position and check that the side/no. plate lights are working. Activate the rear fog lamp using the control panel and check that it is working properly.Operate the direction indicators using the stalk lever and check that they are working properlyPress the brake pedal and check that the brake lights come on	Continue to Step 1	Parking lights not working	Continue as instructed See table   I02  PARKING LIGHTS NOT WORKING
			Side/no. plate lights not working	Continue as instructed See table   I01  SIDE LIGHTS/NO. PLATE LIGHTS NOT WORKING
			Hazard warning lights not working	Continue as instructed See table   I39  TURN SIGNALS DO NOT WORK WHEN HAZARD KEY IS PRESSED
			Direction indicators not working	Continue as instructed See table   I10  DIRECTION INDICATORS / HAZARD WARNING LIGHTS
			Rear fog lamps not working	Continue as instructed See table   I21  REAR FOG LAMPS NOT WORKING
			Brake lights not working	Continue as instructed See table   I14  BRAKE LIGHTS AND THIRD BRAKE LIGHT NOT WORKING
1	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Using the Examiner check, in the Instrument Panel Node ambient, that there are no errors and the following parameters are present	Continue to Step 5	Impossible to connect with the Instrument Panel control unit	Continue to Step 2
			There are errors	Continue in accordance with the instructions for the diagnostic equipment
2	ELECTRICAL POWER SUPPLY CHECK	All OK	Problems met	Operation
	Check that the Instrument Panel Node electrical power supply is correct	Continue to Step 3	Positive and/or earth electrical power supply fault.	Replace the defective component (if a fuse is involved, search for the cause of the problem).
3	CHECK ELECTRICAL CONNECTIONS	All OK	Problems met	Operation
	Check the electrical connections between the Body Computer and the Instrument Panel, in particular that each individual pin is correctly connected.	Continue to Step 4	Electrical connections not working.	Restore damaged electrical connections.
4	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Using the Examiner, check the possibility of connecting with the Instrument Panel Node	Continue to Step 6	Impossible to connect with the Instrument Panel	Replace the instrument panel Op. 5060B11
5	CHECK WITH ACTIVE DIAGNOSIS	All OK	Problems met	Operation
	With the Examiner in Instrument Panel ambient, check, in active diagnosis, that the lights check warning light is correctly activated	Continue to Step 6	The component in question is not activated	Replace the instrument panel Op. 5060B11
6	CHECKING WITH DIAGNOSTIC EQUIPMENT	All OK	Problems met	Operation
	Using the Examiner, check, in the Body Computer Node ambient, that there are no errors and the specific parameter varies	Continue to Step 1	Impossible to connect with the Body Computer control unit	Continue to Step 7
			There are errors	Continue in accordance with the instructions for the diagnostic equipment
			The parameter values do not change	Continue to Step 10
7	ELECTRICAL POWER SUPPLY CHECK	All OK	Problems met	Operation
	Check that the Body Computer Node electrical power supply is correct	Continue to Step 8	Positive and/or earth electrical power supply faulty	Replace the component involved (if a fuse is involved, search for the cause of the problem)
8	CHECK ON CONNECTIONS	All OK	Problems met	Operation
	Check the continuity of the wiring between the various bulbs and the Body Computer Node	Continue to Step 9	Electrical connections not working	Restore damaged electrical connections
9	CHECK ON CONNECTIONS	All OK	Problems met	Operation
	Using the Examiner, check the possibility of connecting with the Body Computer Node	Continue to Step 6	Impossible to connect with the Body Computer control unit	Replace the Body Computer Node Op.   5505A32
10	CHECK ON CONNECTIONS	All OK	Problems met	Operation
	Check the continuity of the wiring between the various bulbs and the Body Computer Node	Continue to Step 11	Electrical wiring not working	Renew the damaged wiring
11	CHECK ON CORRECT OPERATION	All OK	Problems met	Operation
	Check that the fault is no longer present	End of diagnosis	The fault persists	Continue to Step 1