2400073 - 1020D14 front crank shaft oil seal cover - r + r and replace seals for versions with oil pump on crank shaft, timing side

Removing ( Refitting ) Position the vehicle on the ramp Proceed with removal  - 1048A10  air cleaner filtering element - replace Proceed with removal  - 7055A43  central front grille - r r Proceed with removal  - 4450B04  right front wheel r r Proceed with removal  - 7055B66  Engine compartment DUST SHIELD protection in right front wheel arch - R.R. Proceed with removal  - 7055B91  Right front WHEEL ARCH LINER - R.R. Proceed with removal  - 1092B40  air conditioner compressor/alternator drive belt - r + rProceed with the removal. Proceed with removal  - 1056B60  single fuel manifold pipe, with injectors - r + r Proceed with removal  - 1032B10  toothed timing belt - r + r for timing adjustment or replacementRefit the power unit timing side rigid mount temorarily and secure with bolts.Refit the power unit timing side flexible mounting block and secure with nuts. Proceed with removal  - 1088C14  water pump - r + r with drive belt removed Proceed with removal  - 1032B44  toothed drive pulley - r + r with timing belt removed Proceed with removal  - 1072C44  exhaust manifold heat shield on bulkhead - r+r Proceed with removal  - 1072C16  exhaust manifold with catalytic converter - r r Proceed with removal  - 1020A20  crank case oil sump - r + r clean seals for sealant application Proceed with removal  - 1084B28  engine oil intake pump - r + r with crankcase sump removed1. Disconnect the electrical connection for the rpm sensor.

	Name	Connector
1	Rpm sensor	K46

2. Disconnect the electrical connection from the engine oil pressure warning light switch.

	Name	Connector
2	Engine oil pressure sensor (switch)	K30

3. Undo the bolt and remove the rpm sensor. 1. Undo botls (1a) and remove crankshaft oil seal cover. Refitting ( Removing ) 1. Fit the crankshaft front cover (1a), complete with gasket, and fix it tightening the bolts (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	CRANKSHAFT FRONT COVER	M6	0.9 ÷ 1.1

Replace the rear wheel rpm sensor in its housing and fix it using the bolt.Connect the electrical connection to the engine oil pressure warning light switch.Connect the electrical connection for the rpm sensor. Proceed with refitting  - 1084B28  engine oil intake pump - r + r with crankcase sump removed . Proceed with refitting  - 1020A20  crank case oil sump - r + r clean seals for sealant application . Proceed with refitting  - 1072C16  exhaust manifold with catalytic converter - r r . Proceed with refitting  - 1072C44  exhaust manifold heat shield on bulkhead - r+r . Proceed with refitting  - 1032B44  toothed drive pulley - r + r with timing belt removed . Proceed with refitting  - 1088C14  water pump - r + r with drive belt removed . Undo the nuts, then remove the timing side power unit support flexible mounting .Undo the bolt and remove the power unit timing side rigid engine mount. Proceed with refitting  - 1032B10  toothed timing belt - r + r for timing adjustment or replacement . Proceed with refitting  - 1056B60  single fuel manifold pipe, with injectors - r + r . Proceed with the refitting . Proceed with refitting  - 1092B40  air conditioner compressor/alternator drive belt - r + r . Proceed with refitting  - 7055B91  Right front WHEEL ARCH LINER - R.R. . Proceed with refitting  - 7055B66  Engine compartment DUST SHIELD protection in right front wheel arch - R.R. . Proceed with refitting  - 4450B04  right front wheel r r . Proceed with refitting  - 7055A43  central front grille - r r . Proceed with refitting  - 1048A10  air cleaner filtering element - replace . Refill the engine oil lubrication system  - 0010T11  engine oil check level and top up . Refill the engine cooling system with coolant  - 0010T20  coolant change . Remove the car from the ramps.