2400779 - 7030B48 FIXED REAR TRANSPARENT section of sliding roof - R.R .

Removing ( Refitting )  - 7040A44  facia lh side cover - r r - 7040A45  facia rh side cover - r r - 7065C34  l/h or r/h sun blind (one) - r+r (right and left)  - 7040E10  front courtesy light - r+r - 7040H08  oddment shelf on roof trim r r - 7040H40  Front. PILLAR COVER for third SIDE WINDOW (one), left or right - R.R. (right and left)  - 7040H36  central trim lower element - r r (right and left)  - 7040H38  central pillar upper element - r r (right and left)  - 7040H66  LEFT REAR SIDE TRIM, WITH REAR PARCEL SHELF SUPPORT - R.R . - 7040H67  RIGHT REAR SIDE TRIM, WITH REAR PARCEL SHELF SUPPORT - R.R . - 7040H42  rear pillar trim - r r (right and left)  - 7040E12  central courtesy light - r+r (right and left)  - 7065C30  interior l/h or r/h grab handle (one) - r+r (all)  - 7040H14  TRIM for centre roof support - R.R. - 7040H16  roof panel lining - r r - 7030B26  sliding roof blind - r+r with roof panel removed

This procedure involves refitting the fixed glass panel after it has been broken. The glass is not removed and refitted.

Refitting ( Removing ) 1. Using a suitable tool, cut and smooth off the bead of sealant (take care over the window glass residues) in the fixed window frame, so as to leave a thickness of between 0.25 and 1 mm, without scratching the paintwork. The sealant left in the frame will act as a backing for the new bond. 2. Suction all the fragments of glass from the fixed window housing. Suction all the fragments of glass from other parts of the vehicle as well.3. Clean the fixed window seating carefully with compressed air and thoroughly degrease with heptane. If glueing takes place 60 minutes after cutting and smoothing the bead of sealant, treat the sealant surface with the specific activator and wait 15 minutes before fixing the fixed window.

	Type	Component	Name	Qty.
3	-	SUN ROOF FIXED TRANSPARENT SECTION HOUSING	PUR activator	-

Touch up the paintwork if necessary.4. Fit the special shims. Check that the new window is not damaged.1. Degrease the screen-printed edge of the new window using heptane.2. Using the swab (2a) supplied in the kit, apply the glass adhesion promoter (primer) (2b) on the printed perimeter.

Wait for 15 minutes before carrying out the next operation to give the primer thinner time to evaporate.

Make sure that the sliding front roof is completely closed (end of travel).1. Fit the suction pads (1b) on the glass (1a) and carry out a test fitting, then centre the glass perfectly in the housing. 2. Also check the reciprocal position of the glass (1a) along the front profile (2a) and the rear profile (2b): check that the measurements shown in the diagram are correct; if necessary, adjust the special shims (2c). 3. After the window has been centred, mark the reciprocal position of the glass and the housing using strips of adhesive tape. 1. Cut the strips of adhesive tape.2. Remove the glass. 1. Use an air gun to extrude a bead of sealant as evenly as possible along the perimeter of the window.

	Type	Component	Name	Qty.
1	Sealant	SUN ROOF FIXED WINDOW	Product n. 71711976	-

Begin applying the sealant from the rear and continue without breaks around the entire edge of the window.

1. With the assistance of a second operator, fit the windscreen in its seating immediately after applying the sealant and bed it in place. 2. Reach the correct position for the glass (2a) along the front profile (2b) and the rear profile (2c) (follow the measurements shown in the diagram). 1. Position the belt (1a) as shown in the diagram from inside the vehicle and tension it so that the glass (1b) is kept in the correct position as indicated in the previous points. Before refitting the interior components of the car, check that there are no leaks by carrying out a water test. - 7030B26  sliding roof blind - r+r with roof panel removed - 7040H16  roof panel lining - r r - 7040H14  TRIM for centre roof support - R.R. - 7065C30  interior l/h or r/h grab handle (one) - r+r (all)  - 7040E12  central courtesy light - r+r - 7040H42  rear pillar trim - r r (right and left)  - 7040H67  RIGHT REAR SIDE TRIM, WITH REAR PARCEL SHELF SUPPORT - R.R . - 7040H66  LEFT REAR SIDE TRIM, WITH REAR PARCEL SHELF SUPPORT - R.R . - 7040H38  central pillar upper element - r r (right and left)  - 7040H36  central trim lower element - r r (right and left)  - 7040H40  Front. PILLAR COVER for third SIDE WINDOW (one), left or right - R.R. (right and left)  - 7040H08  oddment shelf on roof trim r r - 7040E10  front courtesy light - r+r - 7065C34  l/h or r/h sun blind (one) - r+r (right and left)  - 7040A45  facia rh side cover - r r - 7040A44  facia lh side cover - r r - 7065C34  l/h or r/h sun blind (one) - r+r (left and right)  - 7065C30  interior l/h or r/h grab handle (one) - r+r (all)

Wait six hours before moving the car.