1036C14 CAMSHAFT IN CYLINDER HEAD - R R WITH HEAD REMOVED - Fiat - IDEA - eLearn

2401007 - 1036C14 camshaft in cylinder head - r r with head removed

) 1. Position the upper cylinder head (1a) in the vice using the tool (1b).

	Name	Country
1b	Mount	1.860.470.001

1. Undo bolts (1a) and remove vacuum unit (1b).2. Remove the gasket.3. Undo the bolts (3a) and remove the pressure pump (3b) complette with O-Ring.4. Remove the coupling.

1. Undo the bolts (1a) and remove the cam angle sensor (1b).

Temporarily remove the tool fitted previously on the exhaust side camshaft.

	Name	Country
-	Gauge	1.870.896.900

Check that the end float of the camshaft is within the recommended values using a dial gauge.

	Measurement		Value
-	End float (mm)		0.15 ÷ 0.34

If the end float of the camshaft is not within the recommended values, when reassembling the cylinder head, replace the worn components. 1. Remove the plug (1a) and fit the tool (1b) on the inlet side camshaft.

Fit the tool positioning it with the references in a horizontal direction and checking that it is correctly inserted in the housing in the camshaft.

	Name	Country
1b	Gauge	1.870.896.900

2. Undo the camshaft sprocket fixing bolts.

1. Remove the camshaft timing tools from the camshaft housing.

	Name	Country
1	Gauge	1.870.896.900

2. Release the camshafts (2a) as necessary and remove the camshaft gears (2b).Remove the camshafts completely.

Refitting ( Removing

) Place the camshafts back in their housings.Place the camshaft gears back in their housings and secure them without tightening the bolts. 1. Fit the camshaft timing tools.

Fit the tool positioning it with the millings in a horizontal position and checking that it is correctly inserted in the housings in the camshafts.

	Name	Country
1	Gauge	1.870.896.900

2. Tighten the camshaft sprocket fixing bolts to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
2	Bolt	CYLINDER HEAD EXTENSION	M12	(Camshaft side) 10.8 ÷ 13.2

1. Place the cam angle sensor (1a) back in its housing and secure it tightening the bolt (1b) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1b	Bolt	CAM ANGLE SENSOR	M6	(Camshaft housing side) 0.6 ÷ 0.8

1. Place the pressure pump (1a), complete with coupling (1b) and new O-ring, back in its housing and fix it tightening the bolts (1c) to the recommended torque.

	Fastening	Component	Ø	Value(daNm)
1c	Bolt	PRESSURE PUMP	M7	(Camshaft housing side) 1.4 ÷ 1.7

2. Place the vacuum unit (2a), complete with gasket (2b), back in its housing and secure it tightening the bolts (2c) to the recommended torque.

Follow the order shown in the diagram for each tightening sequence. Tighten to 2.0 daNm in two stages: an initial stage of 0.5 daNm following tightening to 1.8 - 2.2 daNm.

	Fastening	Component	Ø	Value(daNm)
2c	Bolt	BRAKE SERVO VACUUM PUMP	M8	(Cylinder head side) 1.8 ÷ 2.2

Remove the support tool, complete with upper cylinder head from the vice and separate them.