7035A14 (BONDED TYPE) WINDSCREEN GLASS - R.R. - INCLUDES. CLEANING EDGES OF GLASS AND HOUSING IN BODYSHELL - Alfa - 166 - eLearn

3315163 - 7035A14 (Bonded type) windscreen GLASS - R.R. - Includes. cleaning edges of glass and housing in bodyshell

) - 7055A18 Windscreen base TRIM - R.R. - 5050B34 windscreen wiper arm/s complete with blade - r+r - 7025A66 l/h or r/h bonnet lid support damper (one) - r+r - 7025A14 Bonnet LID - R.R. - 7030B34 sliding roof compartment decorative seal - r+r - 7040E40 modular front courtesy light - r r - 7040E28 courtesy light on sun blind - r r- 7040E14 l/h or r/h side courtesy light (one) - r+r - 7040H30 front pillar trim - r r - 7055A10 MOULDING on roof panel (one), left or right - R.R. - 7065C30 interior l/h or r/h grab handle (one) - r+r - 7065C34 l/h or r/h sun blind (one) - r+r - 7065C59 interior rear view mirror with automatic antiglare device - r r - 7065C68 rear view mirror - r+rProtect the facia and wings using covers.1. Remove the press-fitted roof panel moulding retaining studs from both sides of the car.

1. Unscrew the three bolts located under the courtesy light which secure the front part of the roof panel.

1. Working from outside the car, remove the five spacers located between window and body.

1. Working inside the car, use a vibrating cutter ( 1a) with blade (1b) to cut the sealant strip along the sides and on the upper part of the windscreen.

	Name	Country
1a	Vibrating knife	1.823.011.000

	Name	Country
1b	Blade	1.870.691.000

2. Place a set of adhesive tape strips between window and roof panel to prevent the window slipping once the sealant has been cut.3. Disconnect the electrical connection and fold the connector and wires back onto the glass. Secure in place using adhesive tape.

	Name	Connector
3	Heated windscreen	P56

4. Working from outside the car, use the vibrating cutter fitted with a new blade to cut the sealant strip along the bottom of the windscreen. Take care not to cut the wiring previously folded back onto the windscreen.

	Name	Country
4	Blade	1.870.692.000

5. Apply sucker handles to the windscreen.6. Cut the strips of adhesive tape and remove the windscreen with the aid of a second operator.

Refitting ( Removing

) 1. Use vibrating knife (1a) and blade (1b) to cut and level the sealant strip in the windscreen compartment. Leave 0.25 /1 mm thickness without scratching the paint and ensure the locating holes (1c) present at the corners of the windscreen are left free.

	Name	Country
1a	Vibrating knife	1.823.011.000

	Name	Country
1b	Blade	1.870.691.000

2. Clean the windscreen housing carefully using compressed air and degrease thorougly using heptane.Touch up the paintwork if necessary.Remove the trim moulding at the top of the windscreen.

1. Use vibrating cutter (1a) and blade (1b) to cut and level the sealant strip to reduce its thickness. Leave 0.25/1 mm and remove the remains of locating pins (1c).

	Name	Country
1a	Vibrating knife	1.823.011.000

	Name	Country
1b	Blade	1.870.691.000

2. Clean the screen-printed area around the edge carefully using compressed air and degrease thorougly using heptane.Check that the glass is undamaged and is not scratched or grazed. 3. Fit a new trim moulding at the top of the windscreen.

1. Fit the five spacers (1a) removed previously in the windcreen housing using double-sided adhesive tape (1b).2. If the original locating pins are not available, fit and centre provisionally.Mark the reciprocal positions of windscreen and housing using strips of adhesive tape.Fit appropriate spacers to the lower part of the screen to support the glass.Cut the adhesive tape strips and remove the windscreen.Fit the three clips securing the trim moulding.3. Use an air gun to extrude a sealant strip around the edge of the windscreen. Begin from the middle.4. Working with the aid of a second operator, use sucker handles to position the windscreen in its housing immediately after applying the sealant. Check it is properly aligned with the adhesive tape strips positioned previously.

1. Fit retaining belt (1a) to apply uniform pressure over the entire windscreen in order to ensure effective mating between glass (1b), sealant (1c) and windscreen (1d).

Check for leaks by applying soapy water around the outer edge and then blowing compressed air through from the inside.Tighten the bolts securing the front of the roof panel. - 7065C68 rear view mirror - r+r - 7065C59 interior rear view mirror with automatic antiglare device - r r - 7065C34 l/h or r/h sun blind (one) - r+r - 7065C30 interior l/h or r/h grab handle (one) - r+r - 7055A10 MOULDING on roof panel (one), left or right - R.R. - 7040H30 front pillar trim - r r - 7040H32 sliding roof switch door panel - r r - 7040E28 courtesy light on sun blind - r r - 7040E40 modular front courtesy light - r r - 7030B34 sliding roof compartment decorative seal - r+r - 7025A14 Bonnet LID - R.R. - 7025A66 l/h or r/h bonnet lid support damper (one) - r+r - 5050B34 windscreen wiper arm/s complete with blade - r+r - 7055A18 Windscreen base TRIM - R.R.