3314417 - 1032B10 toothed timing belt - r + r for timing adjustment or replacement

Removing ( Refitting ) Position the vehicle on the ramp Proceed with the removal  - 7040D12  engine front side cover (one) lh or rh - r r (Right side). Proceed with the removal  - 7040D14  engine bay rear side cover (one) lh or rh - r r (Right side). Proceed with removal - 4450B04 right front wheel r r . Proceed with removal  - 7055B54  under-engine guard - r r . Proceed with the removal  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with removal  - 1092G10  single engine belt r r . Proceed with removal  - 1092A10  Crankshaft services PULLEY - R.R. . Proceed with removal  - 1092G21  engine component single belt fixed tensioner - r rwith belt removed . Proceed with removal  - 1016A10  sound-proofing cover - r + r . Proceed with removal  - 1008C10  power unit upper reaction link r r . Proceed with removal  - 1032D12  timing system protective cover(s) - r + r . 1. Slacken the nut on the timing belt moving tensioner.2. Prise off and remove the timing belt. Refitting ( Removing ) 1. Remove the plugs (1a) and fit the camshaft timing tools (1b) in the cylinder head extension from the exhaust side.

Check that the tool is correctly fitted in the housing in the exhaust side camshaft.

	Name	Country
1b	Gauge	1.870.896.900

2. Tighten the toothed driven pulley bolt. 1. Undo the bolt for the crankcase front cover shown in the diagram. Temporarily fit the timing drive belt on the drive pulley. Check that the belt teeth are correctly inserted in the pulley grooves.2. Fit the tool (2a) and secure it gauged bolts (2b)

To allow the engagement of the locating dowel on the timing drive belt drive pulley in the opening in the tool, rotate the crankshaft using small movements.

	Name	Country
2a	Template	1.860.905.000

	Name	Country
2b	Calibrated screw	1.860.905.010

1. Completely fit the timing belt.2. Use a screwdriver to lever in the hole (2a) until the reference on the tensioner (2b) lines up with the reference hole (2c) and, in this position, tighten the tensioner nut (2d) to torque.

	Fastening	Component	Ø	Value(daNm)
2d	Nut	MOBILE TIMING TENSIONER	M10	4.5 ÷ 5.5

3. Tighten the toothed drive pulley bolt to the specified torque.

	Fastening	Component	Ø	Value(daNm)
3	Bolt	TIMING GEAR DRIVEN PULLEYS	M12	(Exhaust camshaft side) 12.0

Remove the timing tools.

	Name	Country
-	Gauge	1.870.986.900

	Name	Country
-	Template	1.860.905.000

	Name	Country
-	Calibrated screw	1.860.905.010

Rotate the crankshaft through two revolutions.Check once again that the timing is correct by refitting the timing tools.

Only fit the exhaust camshaft side template because the inlet side one is not accessible.

Check that the tensioning references on the timing belt tensioner are aligned. Tighten the bolt for the crankcase front cover previously removed. Tighten the plug in the camshaft housing for fitting the exhaust side timing tool. Proceed with refitting  - 1032D12  timing system protective cover(s) - r + r . Proceed with refitting  - 1008C10  power unit upper reaction link r r . Proceed with refitting  - 1016A10  sound-proofing cover - r + r . Proceed with refitting  - 1092G21  engine component single belt fixed tensioner - r rwith belt removed . Proceed with refitting  - 1092A10  Crankshaft services PULLEY - R.R. . Proceed with refitting  - 1092G10  single engine belt r r . Proceed with the refitting  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (Right side). Proceed with refitting  - 7055B54  under-engine guard - r r . Proceed with refitting - 4450B04 right front wheel r r . Proceed with the refitting  - 7040D14  engine bay rear side cover (one) lh or rh - r r (Right side). Proceed with the refitting  - 7040D12  engine front side cover (one) lh or rh - r r (Right side). Remove the car from the ramps.