3315488 - Introduction - MANUAL GEARBOX AND DIFFERENTIAL

DESCRIPTION

Structure of the gearbox

The structure of the gearbox consists of:

  • a gearbox casing with a "closed end" configuration with the rear cover eliminated.This contains and support the main and layshaft, the gear engagement selector forks and rods and the gear selector/engagement device.
  • the bell housing which contains the clutch, the thrust bearing and the control device.
1, Main shaft 2, 5 th speed drive gear 3, 4 th speed drive gear 4, 3 rd speed drive gear 5, 2 nd speed drive gear 6, 1 st speed drive gear 7, Reverse speed drive gear 8, Layshaft 9, Satellite gears 10, Planet gears 11, Ring gear 12, Gearbox casing 13, Clutch casing 14, Differential support housing

Main shaft

The main shaft consists of:

  • 1st , Reverse and 2nd speed gears
  • 3rd , 4th , 5th /6th speed gears, fitted on needle bearings with the synchronizers
The main shaft is supported by means of two high precision conical bearings.The main shaft (1) rear bearing has a Viton seal (2) which compensates for axial thermal expansion of the gearbox casing and the main shaft.

The seal makes it possible to:

  • reduce the wear of the synchronizers
  • improve the matching of the gears
  • reduce the noise from the bearings
  • improve the manoeuvrability of the gearbox.

Layshaft

The layshaft consists of:

  • 1st and 2nd speed gears, fitted on needle bearings with synchronizers
  • 3rd , 4th and 5th /6th speed gears fitted on the shaft.
The layshaft is supported by means of two high precision conical bearings.

Gears

The gears are the following type:

  • helical toothed for the forward speeds
  • straight toothed for Reverse.

All the gears have been designed with "high cover factor" teeth, i.e. when one of the matching teeth is in contact, the next tooth has already started meshing which has the advantage of:

  • reducing transmission irregularities
  • reducing operating noise.
The teeth on the gears for 2 nd speed, 5 th speed and the final drive have been "super-finished" after the heat treatment.

Synchronizers

The synchronizers for all the gears are brass, baulk ring "Borg-Warner" of the following type:

  • triple cone (1) for 1st and 2nd speeds
  • double cone (2) for 3rd speed
  • single cone (3) for 4th and 5th /6th speed

Multiple cone synchronizers make it possible to:

  • distribute the lever engagement load over several cones
  • facilitate the engagement of the gears.

Gear selection/engagement system

There are four selection levels for the gear selection/control system with the gear positioner fitted with a bearing.The system ensures that it is impossible to accidentally engage Reverse gear as it is on a separate level.

Two bushes (6) with a Permaglide covering have been used to reduce friction at:

  • the couplings between the gear selector/engagement control shaft and the gearbox casing
  • the couplings for the selector fork rods and the gearbox casing.

The bushes make it possible to:

  • achieve improved sliding
  • ensure better gear engagement precision.
1, Selector pawl 2, 1 st - 2 nd speed engagement/selector fork 3, 3 rd - 4 th speed engagement/selector fork 4, 5 th - 6 th speed engagement/selector fork 5, Reverse gear engagement/selector fork 6, Permaglide bushes 7, Gear engagement lever

Differential

The clutch operation consists of:

  • a crown wheel and pinion reduction
  • a differential housing made from two half casings which include the planet and satellite gears.
The differential housing is supported by two conical bearings and the ring gear is fixed by bolts.The drive gear for the speedometer is fitted on the outside of the differential housing.

Clutch control

The clutch control consists of:

  • a fork bearing (1) fitted inside the clutch casing
  • a thrust bearing (2) fitted on the main shaft

The fork bearing is supported by the Permaglide bushes (3) which make it possible to:

  • reduce the force required to operate the clutch pedal
  • eliminate the use of grease
  • limit the wear of the coupling.

Lubrication

In addition to the "whipping effect", the gears are also lubricated by means of ducts inside the:

  • clutch casing and gearbox casing
  • 3rd and 4th speed control rod
  • main shaft.

The improved lubrication of the ducts makes it possible to:

  • improve the efficiency of the lubrication
  • reduce the amount of oil used thanks to the lubrication aimed at the main couplings.
The use of ZC 75 S synthetic multi-grade oil ensures improved manoeuvrability at low temperatures.