3314035 - 1008A44 rear rigid mount - r r (Automatic transmission)

Removing ( Refitting ) Position the vehicle on the ramp. Make sure that the ignition is OFF (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

NameConnector
-Battery  A1B 
 - 7040D12  engine front side cover (one) lh or rh - r r (right)  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right)  - 1016A40  ignition coil cover on cylinder head- r+r .  - 1008C10  power unit upper reaction link r r .  - 4450B10  Front WHEEL (one) - R.R. (left).  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (right)  - 7055B54  under-engine guard - r r .  - 4410A80  damper lower fork - r r .  - 2710A10  drive shaft with joints (one), l/h or r/h - r + r (right)  - 1076B50  exhaust pipe attachment to engine - r + r .  - 2710A30  intermediate drive shaft - r + r with r/h drive shaft removed .  - 2710A31  intermediate drive shaft - r r .  - 1092G10  single engine belt r r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1032D12  timing system protective cover(s) - r + r .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 5530A14  alternator - r+r for versions with air conditioner1. Undo the bolts (1a) and remove the power steering pump drive pulley (1b).
1. Undo the bolts (1a) and move the power assisted steering pump (1b) without disconnecting the pipes.
1. Undo the bolts (1a) and remove the bracket (1b) connecting the power unit rigid rear mounting to the inlet manifold.
1. Fit a suitable engine lifting bracket.2. Fit the safety tools (2a) and (2b) for supporting the power unit.

NameCountry
2aSupport mountings1.870.650.000

NameCountry
2bCrossmember1.820.581.000
1. Undo the nut fixing the rear power unit rigid support to the flexible mounting.2. Undo the bolts fixing the power unit rear flexible mounting to the front suspension frame.3. Undo the bolts (3a) and remove the bracket (3b) connecting the power unit rigid rear support to the crankcase sump.
1. Undo the bolts (1a) and remove the power unit rigid rear support (1b) removing it through the wheel arch.
Refitting ( Removing ) Fit the power unit rigid rear support and fix it to the cylinder block/crankcase tightening the bolts to the recommended torque.

FasteningComponentØValue(daNm)
-BoltPOWER UNIT RIGID REAR MOUNTM8(Engine crankcase side) 2.7 - 3.4

FasteningComponentØValue(daNm)
-BoltPOWER UNIT RIGID REAR MOUNTM10(Engine crankcase side) 6.0 - 7.4
1. Fit the bracket (1a) connecting the power unit rigid rear support to the crankcase sump and fix it using the bolts (1b).2. Tighten the bolts fixing the rear power unit flexible mounting to the front suspension frame to the recommended torque.

FasteningComponentØValue(daNm)
2BoltINTERM RUBBER MOUNTM10(Front suspension frame side) 4.9 - 6.1
3. Tighten the nut securing the rear power unit rigid support to the flexible mounting to the recommended torque.

FasteningComponentØValue(daNm)
3NutPOWER UNIT RIGID REAR MOUNTM10(Flexible mounting side) 3.8 - 4.7
Remove the safety tools used for supporting the power unit.

NameCountry
-Support mountings1.870.650.000

NameCountry
-Crossmember1.820.581.000
Remove the engine lifting bracket.Fit the bracket connecting the power unit rigid rear support to the inlet manifold and fix it using the bolts.1. Place the power assisted steering pump (1a) back in its housing and fix it tightening the bolts (1b) to the recommended torque.

FasteningComponentØValue(daNm)
1bBoltPOWER STEERING PUMPM8(Mount side) 2.1 ÷ 2.6
2. Fit the power assisted steering pump drive pulley (2a) and fix it tightening the bolts (2b) to the recommended torque.

FasteningComponentØValue(daNm)
2bBoltPOWER STEERING PUMP DRIVE PULLEYM8(Power steering pump side ) 2.1 ÷ 2.6
 - 5530A14  alternator - r+r for versions with air conditioner .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 1032D12  timing system protective cover(s) - r + r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G10  single engine belt r r .  - 2710A31  intermediate drive shaft - r r .  - 2710A30  intermediate drive shaft - r + r with r/h drive shaft removed .  - 1076B50  exhaust pipe attachment to engine - r + r .  - 2710A10  drive shaft with joints (one), l/h or r/h - r + r (right)  - 4410A80  damper lower fork - r r .  - 7055B54  under-engine guard - r r .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (right)  - 4450B10  Front WHEEL (one) - R.R. (left).  - 1008C10  power unit upper reaction link r r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right)  - 7040D12  engine front side cover (one) lh or rh - r r (right) Connect the battery terminal (-).Remove the car from the ramp.