3314062 - 1020E10 oil seal cover (one) - l or r - on counter-rotating shafts - r + r and replace seals

Removing ( Refitting ) Place the vehicle on a ramp. - 7040D12  engine front side cover (one) lh or rh - r r (right).  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right).  - 4450B10  Front WHEEL (one) - R.R. .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (right).  - 7055B54  under-engine guard - r r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 5510C14  ignition coil/s - r+r .  - 1016A20  single cam cover - r + r and replace gasket .  - 1092G10  single engine belt r r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1032D12  timing system protective cover(s) - r + r .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1092E24  counter-rotating shaft pulley - r + r with toothed belt removed . For the inlet side right oil cover, proceed as follows:1. Undo the bolts (1a) and remove the power assisted steering fluid reservoir (1b).2. Undo the bolts (2a) and remove the timing belt right side protection (2b).
1. Undo the bolts (1a) and remove the oil cover (1b) complete with oil seal.Remove the oil seal from the cover.
For the exhaust side left oil cover, proceed as follows: - 1032C32  fixed timing system tensioner (one) r + r . 1. Undo the bolts (1a) and remove the oil cover (1b) complete with oil seal and moving timing tensioner (1c).Remove the oil seal from the cover.
Refitting ( Removing ) For the exhaust side left oil cover, proceed as follows:1. Fit a new oil seal (1a) on the oil cover using the tool (1b).

NameCountry
1bFitting tool1.821.247.000
Fit the oil cover, complete with oil seal and moving timing tensioner, and fix it tightening the bolts to the recommended torque.

FasteningComponentØValue(daNm)
-BoltCOUNTER ROTATING SHAFT FRONT COVERM6(Engine crankcase side) 0.8 ÷ 1.0
For the inlet side right oil cover, proceed as follows:1. Fit a new oil seal (1a) on the oil cover using the tool (1b).

NameCountry
1bFitting tool1.821.247.000
Fit the oil cover, complete with oil seal, and fix it tightening the bolts to the recommended torque.

FasteningComponentØValue(daNm)
-BoltCOUNTER ROTATING SHAFT FRONT COVERM6(Engine crankcase side) 0.8 ÷ 1.0
Fit the timing belt side protection and fix it using the bolts.Place the power assisted steering fluid reservoir back in its housing and fix it using the bolts.  - 1092E24  counter-rotating shaft pulley - r + r with toothed belt removed .  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 1032D12  timing system protective cover(s) - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092G10  single engine belt r r .  - 1016A20  single cam cover - r + r and replace gasket .  - 5510C14  ignition coil/s - r+r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 7055B54  under-engine guard - r r .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (right).  - 4450B10  Front WHEEL (one) - R.R. .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right).  - 7040D12  engine front side cover (one) lh or rh - r r (right). Remove the vehicle from the ramp.