3314073 - 1028H21 piston with connecting rod - r r

Removing ( Refitting )  - 7040D12  engine front side cover (one) lh or rh - r r (right and left).  - 7040D30  engine bay front beam cover - r r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right and left).  - 4450B10  Front WHEEL (one) - R.R. (right)  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. .  - 7055B54  under-engine guard - r r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 5510C14  ignition coil/s - r+r .  - 1016A20  single cam cover - r + r and replace gasket .  - 1056B60  single fuel manifold pipe, with injectors - r + r .  - 1048A48  throttle heater sleeve - r r .  - 1072D10  modular inlet manifold - r+r .  - 1092G10  single engine belt r r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1032D12  timing system protective cover(s) - r + r .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 1092E20  counter-rotating shaft drive toothed belts drive pulley - r + r with toothed belt removed .  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1088D10  lower sleeve for coolant outlet from radiator - r + r .  - 1016C11  single cylinder head-r r gasket for versions with air conditioner .  - 1076B50  exhaust pipe attachment to engine - r + r .  - 1020A20  crank case oil sump - r + r clean seals for sealant application . Rotate the crankshaft until the piston for the cylinder concerned is at B.D.C.1. Undo the bolts (1a) and remove the bearing cap (1b) for the cylinder involved.2. Remove the lower big end bearing shell.
1. Remove the connecting rod with the piston.2. Remove the upper big end bearing shell.
Refitting ( Removing ) 1. Fit the connecting rod - piston assembly and upper half-bearing (1a) using a suitable tool (1b).
The connecting rod - piston assembly is fitted in the cylinder block/crankcase with the large references (for the inlet valves) on the piston crowns facing towards the inlet side.
1. Fit the connecting rod cap (1a) complete with half-bearing (1b) and fix it tightening the bolts (1c) to the recommended torque.
The connecting rod cap is fitted so that the number on it is facing the same way as the one stamped on small end (inlet side).

FasteningComponentØValue(daNm)
1cBoltBIG END BEARING CAPSM92.4 ÷ 2.6 + 60?
Use the tool for angular tightening of the connecting rod cap bolts.

NameCountry
-Protractor1.860.942.000
 - 1020A20  crank case oil sump - r + r clean seals for sealant application .  - 1076B50  exhaust pipe attachment to engine - r + r .  - 1016C11  single cylinder head-r r gasket for versions with air conditioner .  - 1088D10  lower sleeve for coolant outlet from radiator - r + r .  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1092E20  counter-rotating shaft drive toothed belts drive pulley - r + r with toothed belt removed .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 1032D12  timing system protective cover(s) - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092G10  single engine belt r r .  - 1072D10  modular inlet manifold - r+r .  - 1048A48  throttle heater sleeve - r r .  - 1056B60  single fuel manifold pipe, with injectors - r + r .  - 1016A20  single cam cover - r + r and replace gasket .  - 5510C14  ignition coil/s - r+r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 7055B54  under-engine guard - r r .  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. .  - 4450B10  Front WHEEL (one) - R.R. (right)  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right and left).  - 7040D30  engine bay front beam cover - r r .  - 7040D12  engine front side cover (one) lh or rh - r r (right and left).