3314088 - 1036C10 camshaft in cylinder head - r r on vehicle

Removing ( Refitting ) Place the vehicle on a ramp. - 7040D12  engine front side cover (one) lh or rh - r r (right).  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right).  - 4450B10  Front WHEEL (one) - R.R. (right).  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (right).  - 7055B54  under-engine guard - r r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 5510C14  ignition coil/s - r+r .  - 1016A20  single cam cover - r + r and replace gasket .  - 1092G10  single engine belt r r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner - 1032D12  timing system protective cover(s) - r + r .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 1092E20  counter-rotating shaft drive toothed belts drive pulley - r + r with toothed belt removed .  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1032B52  toothed driven pulley (one) - r + r (inlet side and exhaust side). 1. Undo the bolts (1a) and move the cam angle sensor (1b) away from the cylinder head.

NameConnector
1bCam angle sensor  K47 
2. Undo the bolts (2a) and remove the camshaft caps (2b).3. Remove the upper half-bearing for the front camshaft support, inlet side.4. Remove the camshafts.5. Remove the lower half-bearing for the front camshaft support, inlet side.6. Remove the front camshaft oil seals.
Refitting ( Removing ) Fit the lower half-bearing for the front camshaft support, inlet side.Fit the camshafts.Fit the upper half-bearing for the front camshaft support, inlet side.Fit the camshaft caps, except those for the 3rd support and fix them tightening the bolts to the recommended torque.

FasteningComponentØValue(daNm)
-BoltCAMSHAFT SUPPORTSM7Cylinder head side 1.3 ÷ 1.6
1. Fit the front camshaft oil seal, exhaust side (1a) using the tool (1b).

NameCountry
1bFitting tool1.821.228.000
1. Fit the front camshaft oil seal, inlet side (1a) using the tool (1b).

NameCountry
1bFitting tool1.821.252.000
Place the cam angle sensor back in its housing and fix it using the bolt. - 1032B52  toothed driven pulley (one) - r + r (inlet side and exhaust side).  - 1032B14  toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner .  - 1092E20  counter-rotating shaft drive toothed belts drive pulley - r + r with toothed belt removed .  - 1092E10  counter-rotating shaft drive toothed belt - r + r .  - 1032D12  timing system protective cover(s) - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092G10  single engine belt r r .  - 1016A20  single cam cover - r + r and replace gasket .  - 5510C14  ignition coil/s - r+r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 7055B54  under-engine guard - r r .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (right).  - 4450B10  Front WHEEL (one) - R.R. (right).  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right).  - 7040D12  engine front side cover (one) lh or rh - r r (right). Remove the vehicle from the ramp.