3314195 - 1088D26 rigid intake pipe to water pump - r+r for versions with a/c (Automatic transmission)

Removing ( Refitting ) Position the vehicle on the ramp. Make sure that the ignition is OFF (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

NameConnector
-Battery  A1B 
 - 7040D12  engine front side cover (one) lh or rh - r r (right and left)  - 7040D30  engine bay front beam cover - r r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (left).  - 1016A40  ignition coil cover on cylinder head- r+r .  - 7055B54  under-engine guard - r r .  - 1072C12  exhaust manifold - r r .  - 1092G10  single engine belt r r .  - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling .  - 5040A44  air conditioner dehydrating filter/accumulator - r+r .  - 5040A20  air conditioner compressor - r+r - includes fluid level check and top up if necessary .  - 5040A26  compressor mount - r r . 1. Disconnect the lower coolant oulet hose from the radiator from the rigid inlet pipe to the water pump.
Collect the coolant in a suitable container.
2. Disconnect the water return pipe from the heater from the rigid inlet pipe to the water pump.3. Disconnect the supply pipe from the tank from the rigid inlet pipe to the water pump.4. Disconnect the coolant outlet pipe from the engine oil heat exchanger from the rigid inlet pipe to the water pump.5. Undo the bolts fixing the coolant supply pipe to the engine oil heat exchanger.6. Undo the bolts (6a) and the nut (6b), then remove the rigid inlet pipe to the water pump (6c).Remove the gasket.
Refitting ( Removing ) 1. Fit the rigid inlet pipe to the water pump (1a), complete with gasket, and fix it tightening the bolts (1b) and the nut (1c) to the recommended torque.

FasteningComponentØValue(daNm)
1bBoltCOOLANT PUMP RIGID INLET PIPEM6Cylinder head side 0.8 - 1.0

FasteningComponentØValue(daNm)
1cNutCOOLANT PUMP RIGID INLET PIPEM8Cylinder head side 2.1 - 2.6
2. Tighten the bolts fixing the coolant supply pipe to the engine oil heat exchanger.3. Connect the coolant pipe from the engine oil heat exchanger to the rigid inlet pipe to the water pump.4. Connect the system supply pipe from the tank to the rigid inlet pipe to the water pump.5. Connect the water return pipe from the heater to the rigid inlet pipe to the water pump.6. Connect the lower coolant outlet hose from the radiator to the rigid inlet pipe to the water pump.
 - 5040A26  compressor mount - r r .  - 5040A20  air conditioner compressor - r+r - includes fluid level check and top up if necessary .  - 5040A44  air conditioner dehydrating filter/accumulator - r+r .  - 5040A10  Air conditioning refrigerant CIRCUIT - Draining and Refilling .  - 1092G10  single engine belt r r .  - 1072C12  exhaust manifold - r r .  - 7055B54  under-engine guard - r r .  - 1016A40  ignition coil cover on cylinder head- r+r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (left).  - 7040D30  engine bay front beam cover - r r .  - 7040D12  engine front side cover (one) lh or rh - r r (right and left) Supply the cooling system with the recommended fluid.

TypeComponentNameQty.
-Fluid [l]ENGINE COOLING CIRCUITAlfa Romeo Climafluid Super Permanent -407.9
Connect the battery terminal (-).Remove the car from the ramp.