1088C20 WATER PUMP - R + R WITH ENGINE REMOVED (AUTOMATIC TRANSMISSION) - Alfa - 166 - eLearn

3315368 - 1088C20 water pump - r + r with engine removed (Automatic transmission)

) 1. Undo the bolts (1a) and remove the upper timing belt guard (1b).2. Undo the bolts (2a) and remove the single drive belt drive pulley (2b).3. Undo the bolts (3a) and remove the lower timing belt guard (3b).4. Slacken the counter-balance shafts belt tensioner nut and remove the counter-balance shafts drive belt.5. Loosen the timing belt tensioner nut.6. Remove the timing belt.

1. Undo the bolt (1a) and remove the left side timing belt guard (1b).2. Undo the bolts (2a) on the inlet side camshaft pulley, using the tool (2b) for counter-torque.

	Name	Country
2b	Counter-torque	1.822.155.000

3. Remove the inlet side camshaft pulley.4. Undo bolts (4a) and remove water pump (4b) complete with O-ring (4c).

Refitting ( Removing

) 1. Fit the water pump (1a) complete with new O-ring (1b) and fix it tightening the bolts (1c) to torque.

	Fastening	Component	Ø	Value(daNm)
1c	Bolt	ORDINARY PREPARATION	M6	1.7 - 2.1

2. Fit the inlet side camshaft pulley (2a) and fix it using the bolts (2b) without tightening them.3. Fit the left side timing belt guard (3a) and fix it using the bolt (3b).Loosen the bolt on the exhaust side camshaft pulley using the tools for counter-torque.

	Name	Country
-	Counter-torque	1.822.146.000

	Name	Country
-	Counter-torque	1.822.156.000

1. Disconnect the electrical connections from the ignition coils.

	Name	Connector
1	Ignition coil	A30

2. Disconnect the earth lead from the cylinder head.3. Disconnect the high-tension leads (3a) from the spark plugs using the tool (3b).

	Name	Country
3b	Pliers	1.820.636.000

4. Disconnect the oil vapour recovery pipe from the rocker cover.

Undo the bolts and remove the bracket complete with ignition coils and high-tension leads.Undo the bolts and remove the rocker cover complete with gasket.1. Fit the tool (1a), complete with dial gauge (1b), in the housing of the spark plug for cylinder no. 1.

	Name	Country
1a	Extension	1.825.013.000

Rotate the crankshaft until the piston for cylinder no. 1 is at T.D.C. at the power stroke. Undo the bolts an remove the third caps from the inlet and exhaust camshafts.2. Fit the tool (2a) in place of the removed camshaft caps, and fix it tightening the bolts (2b) to torque.

Check that the camshaft cam profile matches the tool perfectly.

	Name	Country
2a	Gauge	1.825.041.000

Fit the timing belt.1. Apply maximum tension to the timing belt using the tool.

	Name	Country
1	Key	1.822.149.000

2. Tighten the timing belt tensioner nut to torque.

	Fastening	Component	Ø	Value(daNm)
2	Nut	MOBILE TIMING TENSIONER	M8	2.1 - 2.6

3. Tighten the bolts (3a) of the inlet side camshaft pulley, using the tool (3b) for counter-torque.

	Name	Country
3b	Counter-torque	1.822.155.000

4. Tighten to torque the bolt (4a) on the exhaust side camshaft pulley, using the tools (4b) for counter-torque.

	Fastening	Component	Ø	Value(daNm)
4a	Bolt	TIMING GEAR DRIVEN PULLEYS	M12	10.0 - 12.4

	Name	Country
4b	Counter-torque	1.822.146.000

	Name	Country
4b	Counter-torque	1.822.156.000

Undo the bolts and remove the tool.

	Name	Country
-	Gauge	1.825.041.000

Fit the camshaft caps removed previously and tighten the bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CAMSHAFT CAPS	M7	1.3 - 1.6

Rotate the crankshaft through two revolutions.Slacken the timing belt tensioner nut.5. Line up the moving reference (5a) on the timing belt tensioner with the reference hole (5b) using the tool (5c).

	Name	Country
5c	Key	1.822.149.000

Tighten the timing belt tensioner nut to torque.

	Fastening	Component	Ø	Value(daNm)
-	Nut	MOBILE TIMING TENSIONER	M8	2.1 - 2.6

Rotate the crankshaft until the piston of cylinder no. 1 is at T.D.C.1. Position the counter-balance shafts so that the references on the pullies line up with those on the front covers.2. Fit the counter-balance shafts drive belt.

1. Tension the counter-balance shafts drive belt using the tool (1a) so that the reference hole (1b) on the belt tensioner is at the centre of the rotation sector.

	Name	Country
1a	Key	1.822.154.000

2. Tighten the counter-balance shafts belt tensioner nut.

Remove the tool complete with dial gauge.

	Name	Country
-	Extension	1.825.013.000

Fit the spark plug for cylinder no. 1.Fit the rocker cover complete with gasket and fix it using the bolts. Connect the oil vapour recovery pipe to the rocker cover.Fit the bracket complete with ignition coils and high-tension cables and fix it using the boltsConnect the high tension leads to the spark plugs.Connect the earth lead to the cylinder head.Connect the electrical connections to the ignition coils.Fit the lower timing belt guard and fix it using the bolts.Fit the upper timing belt guard and fix it using the bolts.Fit the single drive belt pulley and tighten the bolts to torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CRANKSHAFT PULLEY	M8	2.4 - 2.9

Fit the fixed single drive belt tensioner and fix it with its bolt.