3314077 - 1032B14 toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner (Automatic transmission)

Removing ( Refitting ) Position the vehicle on the lift. Make sure that the ignition is off (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

	Name	Connector
-	Battery	A1B

 - 7040D12  engine front side cover (one) lh or rh - r r (right and left).  - 7040D30  engine bay front beam cover - r r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right).  - 1072B50  sleeves connecting air capacity box to inlet manifold is - r+r .  - 1016A36  left hand and right hand cam cover - r+r .  - 4450B10  Front WHEEL (one) - R.R. (right).  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right).  - 4130B10  power steering fluid resevoir r r .  - 1092G10  single engine belt r r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G14  engine component single belt mobile tensioner - r + r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1032D12  timing system protective cover(s) - r + r . 1. Rotate the crankshaft so that the references on the camshafts are aligned with the ones on the relevant caps. 1. Slacken the bolts (1a) securing the moving timing belt tensioner and remove the timing belt (1b). Refitting ( Removing ) Remove the 1st cylinder spark plug and slacken the others.1. Fit the tool (1a), complete with dial gauge (1b), in the housing of the spark plug for cylinder no. 1.

	Name	Country
1a	Extension	1.825.013.000

Rotate the crankshaft, using small movements (in both directions), until the piston for cylinder no. 1 is at T.D.C. at the power stroke.

Make sure that the last crankshaft rotation is in the direction of operation.

Fit the timing belt and check that the timing references on the camshafts are aligned.1. Fit the tool (1a) and secure it with the alternator bolt (1b) and the bolt (1c) to the water pump.

The tool tooth (1d) should produce a reaction with the moving part of the timing belt tensioner.

	Name	Country
1a	Belt tensioner	1.860.950.000

2. Act on the nut (2a) for the belt tensioner tool until the moving reference on the belt tensioner (2b) is under the fixed reference. Rotate the crankshaft through two revolutions in its direction of rotation to allow the timing belt to bed in.1. Check that the moving reference on the timing belt tensioner is aligned with the fixed reference.2. If the references do not coincide, slightly discharge the tensioner acting on the tensioning tool nut and make sure that the references are aligned.3. Tighten the timing belt tensioner bolts to the specified torque.

	Fastening	Component	Ø	Value(daNm)
3	Bolt	MOBILE TIMING TENSIONER	M8	Cylinder head side 1.7 - 2.1

Check once again that the timing references on the camshafts are aligned.Remove the belt tensioner tool.

	Name	Country
-	Belt tensioner	1.860.950.000

 - 1032D12  timing system protective cover(s) - r + r .  - 1092G20  engine component single belt fixed tensioner - one - r + r .  - 1092G14  engine component single belt mobile tensioner - r + r .  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1092G10  single engine belt r r .  - 4130B10  power steering fluid resevoir r r .  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right).  - 4450B10  Front WHEEL (one) - R.R. (right).  - 1016A36  left hand and right hand cam cover - r+r .  - 1072B50  sleeves connecting air capacity box to inlet manifold is - r+r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right).  - 7040D30  engine bay front beam cover - r r .  - 7040D12  engine front side cover (one) lh or rh - r r (right and left). Connect the negative (-) battery terminal.Remove the vehicle from the ramp.