1036D58 FRONT SEAL OF R/H OVERHEAD CAMSHAFT - R + R - Alfa - 166 - eLearn

3314235 - 1036D58 front seal of r/h overhead camshaft - r + r

) Position the vehicle on the lift. Make sure that the ignition is off (STOP position), then disconnect the negative battery terminal (refer to op. 5530B10 battery - r+r ).

	Name	Connector
-	Battery	A1B

- 7040D12 engine front side cover (one) lh or rh - r r (right and left). - 7040D30 engine bay front beam cover - r r . - 7040D14 engine bay rear side cover (one) lh or rh - r r (right). - 1072B50 sleeves connecting air capacity box to inlet manifold is - r+r . - 1016A36 left hand and right hand cam cover - r+r . - 4450B10 Front WHEEL (one) - R.R. (right). - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. (right). - 4130B10 power steering fluid resevoir r r . - 1092G10 single engine belt r r . - 1092G14 engine component single belt mobile tensioner - r + r . - 1092G20 engine component single belt fixed tensioner - one - r + r . - 1032D12 timing system protective cover(s) - r + r . 1. Rotate the crankshaft so that the references on the camshafts are aligned with the ones on the relevant caps.

1. Slacken the bolts (1a) securing the moving timing belt tensioner and remove the timing belt (1b) from the driven pullies.

1. Slacken the bolts securing the right cylinder head driven pulley.2. Undo the nut (2a) securing the hub to the camshaft using tools (2b) and (2c) as counter-torque.

	Name	Country
2b	Counter-torque	1.822.146.000

	Name	Country
2c	Counter-torque	1.870.716.000

Undo the bolts securing the right cylinder head driven pulley, previously slackened.1. Fit the tool on the driven pulley and fix it to the hub using the bolts

	Name	Country
1	Extractor	1.820.232.000

2. Tighten the nut of the tool (2a) using the tools (2b) and (2c) as counter-torque, until the hub disengages from the camshaft.

	Name	Country
2b	Counter-torque	1.822.146.000

	Name	Country
2c	Counter-torque	1.870.716.000

Remove the puller.3. Remove the right cylinder head driven pulley.4. Remove the hub.5. Prise off and remove the left head camshaft front seal.

Refitting ( Removing

) 1. Fit the right head camshaft front seal (1a) using the tool (1b).

	Name	Country
1b	Fitting tool	1.870.725.000

Fit the hub.Fit the right cylinder head driven pulley.1. Tighten the left cylinder head driven pulley bolts to the specified torque.

	Fastening	Component	Ø	Value(daNm)
1	Bolt	TIMING GEAR DRIVEN PULLEYS	-	Hub side -

2. Tighten the nut (2a) securing the hub to the camshaft to the specified torque, using the tools (2b) and (2c) as counter-torque.

	Fastening	Component	Ø	Value(daNm)
2a	Bolt	CAMSHAFT HUBS	M14	Camshaft side 9.5 - 11.7

	Name	Country
2b	Counter-torque	1.822.146.000

	Name	Country
2c	Counter-torque	1.870.716.000

Fit the timing belt and carry out the timing (refer to op. 1032B14 toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner ). - 1032D12 timing system protective cover(s) - r + r . - 1092G20 engine component single belt fixed tensioner - one - r + r . - 1092G14 engine component single belt mobile tensioner - r + r . - 1092G10 single engine belt r r . - 4130B10 power steering fluid resevoir r r . - 7055B42 Additional FRONT WHEEL ARCH (one), left or right - R.R. (right). - 4450B10 Front WHEEL (one) - R.R. (right). - 1016A36 left hand and right hand cam cover - r+r . - 1072B50 sleeves connecting air capacity box to inlet manifold is - r+r . - 7040D14 engine bay rear side cover (one) lh or rh - r r (right). - 7040D30 engine bay front beam cover - r r . - 7040D12 engine front side cover (one) lh or rh - r r (right and left). Connect the negative (-) battery terminal.Remove the vehicle from the ramp.