3314053 - 1020A20 crank case oil sump - r + r clean seals for sealant application (Automatic transmission)

Removing ( Refitting )  - 7040D12  engine front side cover (one) lh or rh - r r (right and left).  - 7040D30  engine bay front beam cover - r r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right and left).  - 4450B10  Front WHEEL (one) - R.R. (right)  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r .  - 7055A43  central front grille - r r .  - 7055A41  RIGHT FRONT GRILLE - R.R. .  - 7055B10  Front BUMPER - R.R. .  - 7055B54  under-engine guard - r r .  - 1076B70  exhaust pipe between pre-catalytic converter and catalytic converter - r r .  - 1064A48  sleeve connecting rh exhaust manifold and turbocharger flange - r r and replace gaskets - 2710A31  intermediate drive shaft - r r .  - 1092G10  single engine belt r r .  - 1092G20  engine component single belt fixed tensioner - one - r + r (both).  - 1008C10  power unit upper reaction link r r .  - 1008C16  body link bracket - r r .  - 1008A44  rear rigid mount - r r . 1. Undo the drain plug and drain the engine oil.
Collect the engine oil in a suitable container.
1. Undo the bolts (1a) and remove the lower engine flywheel protection (1b).2. Undo the bolts (2a) and move aside the rpm and timing sensor (2b) complete with mounting bracket and secure it.
1. Undo the bolts fixing the crankcase sump.Heat the area where the crankcase sump matches with the cylinder block/crankcase and cut the sealant.2. Remove the crankcase sump.
Refitting ( Removing )
Check the condition of the sealant on the rear main bearing cap. re-apply if necessary.
Clean the matching surfaces of crankcase sump and cylinder block.Apply the recommended sealant to the entire perimeter of the crankcase sump.

TypeComponentNameQty.
-SealantOIL SUMPLOCTITE 5900-
1. Fitt the crankcase sump (1a) and fix it tightening the bolts (1b) and the bolt (1c) to the recommended torque.

FasteningComponentØValue(daNm)
1bBoltOIL SUMPM7Engine crankcase side 1.3 - 1.6

FasteningComponentØValue(daNm)
1cBoltOIL SUMPM7Engine block side 0.9 - 1.2
Refit the rpm and timing sensor in its seating complete with mounting bracket and tighten its bolts.Fit the lower engine flywheel protection and fix it using the bolts.Tighten the engine oil drain plug to the crankcase sump to the recommended torque.

FasteningComponentØValue(daNm)
--ENGINE OIL DRAIN PLUGM22Crankcase sump side 6.4 - 7.9
 - 1008A44  rear rigid mount - r r .  - 1008C16  body link bracket - r r .  - 1008C10  power unit upper reaction link r r .  - 1092G20  engine component single belt fixed tensioner - one - r + r (both).  - 1092G10  single engine belt r r .  - 2710A31  intermediate drive shaft - r r .  - 1064A48  sleeve connecting rh exhaust manifold and turbocharger flange - r r and replace gaskets .  - 1076B70  exhaust pipe between pre-catalytic converter and catalytic converter - r r .  - 7055B54  under-engine guard - r r .  - 7055B10  Front BUMPER - R.R. .  - 7055A41  RIGHT FRONT GRILLE - R.R. .  - 7055A43  central front grille - r r .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r (left)  - 4450B10  Front WHEEL (one) - R.R. (right)  - 7040D14  engine bay rear side cover (one) lh or rh - r r (right and left).  - 7040D30  engine bay front beam cover - r r .  - 7040D12  engine front side cover (one) lh or rh - r r (right and left). Refill the engine lubrication circuit using the recommended oil.

TypeComponentNameQty.
-OilENGINE LUBRICATION CIRCUITSELENIA 20K6.1