3314284 - 1084C38 engine oil delivery and return pipes to cooling radiator - r + r (Automatic transmission)

Removing ( Refitting ) Position the vehicle on the ramp. Make sure that the ignition is OFF (STOP position), then disconnect the negative battery terminal (refer to op.   5530B10  battery - r+r ).

NameConnector
-Battery  A1B 
 - 4450B10  Front WHEEL (one) - R.R. (left).  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r .  - 7055A41  RIGHT FRONT GRILLE - R.R. .  - 7055A43  central front grille - r r .  - 7055B10  Front BUMPER - R.R. .  - 7055B54  under-engine guard - r r .  - 1084B30  engine oil filter r r .  - 1092G10  single engine belt r r . 1. Disconnect the electrical connection for the insufficient engine oil pressure switch.

NameConnector
1Insufficient engine oil pressure (switch) sensor  K30 
2. Undo and remove the insufficient engine oil pressure switch.
1. Disconnect the electrical connections (1a) and (1b) from the alternator.

NameConnector
1aAlternator  A10A 

NameConnector
1bAlternator  A10B 
2. Undo the bolts (2a) and remove the alternator (2b).
1. Undo the bolt (1a) and the nut (1b) and remove the brackets (1c) supporting the cooling radiator engine oil supply and return pipes.2. Undo the connectors (2a) and disconnect the cooling radiator engine oil supply and return pipes (2b).
1. Undo the bolt (1a) and remove the bracket (1b).2. Undo the bolts (2a) and remove the engine oil supply and return pipes to the cooling radiator (2b).
Refitting ( Removing ) Fit the engine oil supply and return pipes to the cooling radiator and secure them to the radiator using the bolts.Fit the bracket and fix it using the bolt.1. Connect the engine oil supply and return pipes to the cooling radiator (1a) and fix them tightening the connectors (1b) to the specified torque.

FasteningComponentØValue(daNm)
1bConnectorPIPE DELIVERING OIL TO RADIATOR-Rigid rear. power unit support side -

FasteningComponentØValue(daNm)
1bConnectorOIL RETURN PIPE FROM RADIATOR-Rigid rear. power unit support side -
2. Fit the brackets (2a) supporting the engine oil supply and return pipes to the cooling radiator and fix them using the bolt (2b) and nut (2c).
1. Fit the alternator (1a) and fix it tightening the bolts (1b) to the recommended torque.

FasteningComponentØValue(daNm)
1bBoltALTERNATOR ASSEMBLYM8(Mounting bracket side) 1.9 ÷ 2.3
1. Connect the electrical connections (1a) and (1b) checking that there is no contact between the terminal for the B+ cable (1c) and the pin for the D+ cable (1d).

NameConnector
1aAlternator  A10A 

NameConnector
1bAlternator  A10B 
2. Secure the cables using the nuts.
Take special care to ensure that the alternator cables are correctly positioned in their housings, following the routing illustrated exactly.
1. Fit the insufficient engine oil pressure switch and tighten it to the recommended torque.

FasteningComponentØValue(daNm)
1-OIL PRESSURE W/LM14Rigid power unit rear. support. side. 2.0 - 2.5
2. Connect the electrical connection for the insufficient engine oil pressure switch.
 - 1092G10  single engine belt r r .  - 1084B30  engine oil filter r r .  - 7055B54  under-engine guard - r r .  - 7055B10  Front BUMPER - R.R. .  - 7055A43  central front grille - r r .  - 7055A41  RIGHT FRONT GRILLE - R.R. .  - 7055B39  front additional wheel arch half (one), lh or rh, front element - r r .  - 4450B10  Front WHEEL (one) - R.R. (left). Connect the battery terminal (-).Remove the car from the ramp.