3314077 - 1032B14 toothed timing belt - r + r for timing adjustment or replacement versions with air conditioner (Automatic transmission)

Removing ( Refitting )  - 7040D12  engine front side cover (one) lh or rh - r r .  - 7040D14  engine bay rear side cover (one) lh or rh - r r .  - 4450B10  Front WHEEL (one) - R.R. (right).  - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right).  - 1092A12  crankshaft pulley - r+r for versions with air conditioner .  - 1032D12  timing system protective cover(s) - r + r . 1. Slacken the bolts (1a) of the moving timing belt tensioner (1b).2. Prise off and remove the timing belt. Refitting ( Removing ) Carry out op.   1016A42  left hand cylinder head ignition coil cover - r+r . Carry out op.   1072B50  sleeves connecting air capacity box to inlet manifold is - r+r . Carry out op.   5510C14  ignition coil/s - r+r . Carry out op.   1016A36  left hand and right hand cam cover - r+r . Remove the spark plug for cylinder no. 1.1. Fit the tool (1a), complete with dial gauge (1b), in the housing in the spark plug for the 1st cylinder.

	Name	Country
1a	Extension	1.825.013.000

Rotate the crankshaft, using small movements (in both directions) until the piston for cylinder no. 1 is at T.D.C. at the power stroke.

Make sure that the last crankshaft rotation is in the direction of operation.

2. Remove the camshaft caps B and G from the right cylinder head and fit the jigs in their place.

	Name	Country
2	Gauge	1.825.040.000

1. Remove the camshaft caps 4 and 7 from the left cylinder head and fit the jigs in their place.

	Name	Country
1	Gauge	1.825.040.000

Slacken the camshaft pulley bolts using the tool for counter-torque.

	Name	Country
-	Counter-torque	1.822.146.000

Fit the timing belt starting from the drive pulley and continuing in an anti-clockwise direction, making sure that the drive sections are firmly taut.1. Fit the tool (1a) and secure it with the alternator bolt (1b) and the bolt (1c) to the water pump.

The tool lug (1d) should press against the moving part of the timing belt tensioner.

	Name	Country
1a	Belt tensioner	1.860.950.000

2. Adjust the nut (2a) for the belt tensioner tool until the moving reference on the belt tensioner (2b) is under the fixed reference. 1. Tighten the bolts (1a) on the camshaft pullies to the specified torque, using tools (1b) and (1c).

The tightening torque in the table is the nominal figure; the correct value should therefore be calculated in accordance with the length of the extension wrench 1.822.150.000.

	Fastening	Component	Ø	Value(daNm)
1a	Bolt	TIMING GEAR DRIVEN PULLEYS	M10	Camshaft side 6.8 - 8.4

	Name	Country
1b	Counter-torque	1.822.146.000

	Name	Country
1c	Extension for torque wrench	1.822.150.000

Remove the timing jigs.

	Name	Country
-	Gauge	1.825.040.000

Fit the camshaft caps in place of the removed jigs and tighten their bolts to the specified torque.

	Fastening	Component	Ø	Value(daNm)
-	Bolt	CAMSHAFT CAPS	M8	(Cylinder head side) 1.8 ÷ 2.0

Rotate the crankshaft through two revolutions in its direction of rotation to allow the timing belt to bed in.1. Check that the moving reference on the timing belt tensioner is aligned with the fixed reference.2. If the references do not line up, slightly decrease the tension of the tensioner acting on the tensioning tool nut and make sure that the references are aligned.3. Tighten the timing belt tensioner bolts to the specified torque.

	Fastening	Component	Ø	Value(daNm)
3	Bolt	MOBILE TIMING TENSIONER	M8	Cylinder head side 1.7 - 2.1

Remove the belt tensioner tool.

	Name	Country
-	Belt tensioner	1.860.950.000

 - 1016A36  left hand and right hand cam cover - r+r .  - 5510C14  ignition coil/s - r+r .  - 1072B50  sleeves connecting air capacity box to inlet manifold is - r+r .  - 1016A42  left hand cylinder head ignition coil cover - r+r .  - 1032D12  timing system protective cover(s) - r + r - 7055B42  Additional FRONT WHEEL ARCH (one), left or right - R.R. (right).  - 4450B10  Front WHEEL (one) - R.R. (right).  - 7040D14  engine bay rear side cover (one) lh or rh - r r .  - 7040D12  engine front side cover (one) lh or rh - r r .